background image

 

General Valve Installation 

 

Water Pressure 

Minimum 25 PSI 

Electrical Supply 

Uninterrupted 115V AC 

Existing Plumbing 

Free of any deposits or build-ups inside pipes. 

Softener Location 

Locate close to drain and connect according to 
plumbing codes 

Bypass Valves 

Always provide for bypass valve if unit is not 
equipped with one. 

Plumbing  

Softener and or other  water treatment 
equipment should be installed to local 
plumbing codes 

 

 

CAUTION 

 

Do not exceed 120 psi water pressure. 

 

Do not exceed 110°F water temperature. 

 

Do not subject unit to freezing conditions.

 

 

 

 

 

Figure 6. Piping Diagram 

 
1.  Locate the softener tank and brine tank close to a drain where the system will be installed.  The surface should be clean and 

level. 

2.  Perform all plumbing according to local plumbing codes. 

 

Use a ½” minimum pipe or tubing size for the drain line 

 

Use a ¾” pipe or tubing for backwash flow rates that exceed 7 gpm or length that exceeds 20ft (6 m) 

 

ON COPPER PLUMBING SYSTEMS BE SURE TO INSTALL A GROUNDING WIRE BETWEEN THE INLET AND OUTLET PIPING TO 

MAINTAIN GROUNDING. 

3.  Any solder joints near the valve must be done before connecting any piping to the valve.  Always leave at least 6" (152 mm) 

between the valve and joints when soldering pipes that are connected to the valve.  Failure to do this could cause damage to 
the valve. 

4.  If the valve is not installed on the tank, cut the 1” central pipe flush with top of each tank.  Lubricate the large o-ring on the 

valve that seals against the tank.  Screw the valve on to the tank.  Be careful to not cross thread the valve into the tank.  Only 
use silicone lubricant. 

5.  Connect the drain line to the valve. 
6.   Connect  the  brine  line  from  the  valve  to  the  air  check  /  safety  elbow  as  per  figure  7.    Double  check  to  make  sure  all 

connections are assembled correctly and the brass and plastic nuts are tight and secure to prevent leaks. 

 

BRASS NUT

BLUE LOCKING CLIP

 

PLASTIC NUT

3/8” PLASTIC TUBE
INSERT

 

Figure 7. Brine Line Connections View

 

 

Содержание CAN165HIM-100



















Отзывы: