Canature WaterGroup 85UF Скачать руководство пользователя страница 31

Страница: 31 / 36

Follow steps 1 to 3 of Powerhead Removal

above.

Remove three (3) screws from the plate on

the valve body.

Remove the plate from the valve body and

pull the piston assembly from the valve. The

brine valve assembly can also be removed in

this stage.

If only lubricating, remove the piston

assembly, grease it with silicone lubricant

(Part #92360) and put back in.

Replace seal and spacer set as shown.

Place spacer in then a seal and repeat until

finishing with a seal. Important, use the

specialized end spacer and note it’s

placement.

Lubricate the piston assembly with silicone

lubricant (Part #92360) and then replace the

Piston Assembly.

Remove 3 X

Screws

Plate

Seal and

Spacer

Brine Valve

Assembly

Piston

Assembly

POWERHEAD REMOVAL

INSPECTION & REPLACEMENT OF PISTON ASSEMBLY AND SEAL & SPACER KIT

To remove the powerhead:

Remove screw & washer from piston rod link.

Remove powerhead from body.

Remove two (2) bolts securing powerhead to

body.

NOTICE

Do NOT use petroleum-based grease products during

replacement and assembly.

SERVICING YOUR CONTROL VALVE

(CONTINUED)

Содержание 85UF





































Результаты поиска

Содержание 85UF

Отзывы:

Похожие инструкции для 85UF

Бренды по названию

Популярные бренды

Canature WaterGroup 85UF, Руководство пользователя

Результаты поиска

Содержание 85UF

Отзывы:

Похожие инструкции для 85UF

Бренды по названию

Популярные бренды