Canada Docks Do-It-Yourself Small Floating Hexagon Скачать руководство пользователя страница 9 | Manualshive

Страница: 9 / 11

Canada Docks Do-It-Yourself Small Floating Hexagon Скачать руководство пользователя страница 9

SMALL FLOATING HEXAGON INSTRUCTIONS

Canada

Docks

.

ca

TM

Manufactured by: CanadaDocks Inc. 3690 Adjala-Tecumseth Townline RR2 Beeton, ON, Canada L0G 1A0 | 1-877-434-0359 | www.canadadocks.ca

33

34

31

32

30

35

Tie a string to the connecting points of the two

halves to create a straight edge. Install first sheet of

ThruFlow decking (J) centered and aligned against

the straight edge. Install using #12x2” Self Drilling

Tek Screws (B). See ThruFlow Installation instructions.

Ensure the inside edge of the decking rests in the

centre of the joist frame.

Set circular saw to a depth that will not cut into

frame (1-1/8”). Cut off excess ThruFlow decking (J)

as shown.

With Floats firmly attached flip the frame so

the floats are on the ground. PLEASE NOTE:

THREE PERSONS ARE REQUIRED TO SAFELY

FLIP THE FRAME

After installing the first piece, align the next piece

square to your starter piece as shown in diagram.

Install using #12x2” Self Drilling Tek Screws (B). See

ThruFlow Installation instructions.

Set circular saw to a depth that will not cut into

frame (1-1/8”). Cut off excess ThruFlow decking (J) as

shown.

Align the next piece square to the piece above as

shown in the diagram. Install using #12x2” Self Drilling

Tek Screws (B). See ThruFlow Installation instructions.

«
...
7
8
9
10
11
»

Содержание Do-It-Yourself Small Floating Hexagon












Отзывы:

Нет отзывов