Can-Am Spyder RT Limited SE6 Скачать руководство пользователя страница 16 | Manualshive

Страница: 16 / 52

background image

PARTS TO BE INSTALLED

rbl2014-004-021

MIDDLE SIDE PANEL REMOVAL

rmo2010-008-003_k

REMOVAL SEQUENCE

Step 1: Pull rear of panel out of its grommet.
Step 2: Pull bottom of the panel out of its grommet.
Step 3: Pull front of the panel out of its grommet.
Step 4: Unhook top of the panel to remove it.

10. Remove lower wind deflectors.

rbl2014-004-037_a

TYPICAL

1. Lower wind deflector (both sides)
2. Retaining screws

11. Unlock and lift seat to full open position.

12. Remove front and upper retaining screws

from top side panels.

rbl2014-004-038_a

TYPICAL

1. Top side panel (both sides)
2. Front retaining screw
3. Upper retaining screws

13. Remove rear retaining screw from top side

panels.

rbl2014-004-039_a

TYPICAL

1. Top side panel (both sides)
2. Rear retaining screw

14. Remove front retaining screw from top side

panels.

15. Pull out lower part of top side panel to remove

it from grommets and remove panel from ve-
hicle.

NOTE:

Do not remove lower screws

from top

side panel.

16 / 52

2014-1

PREDELIVERY

«
...
14
15
16
17
18
...
»

Содержание Spyder RT Limited SE6





















































Отзывы:

Нет отзывов

Похожие инструкции для Spyder RT Limited SE6

Бренд: LAMAX Страницы: 134

Бренд: Ohlins Страницы: 4

Бренд: LAZER Страницы: 2

Бренд: KTM Power Parts Страницы: 7

Бренд: BMW Motorrad Страницы: 261

Бренд: R&G Страницы: 9

Бренд: Suzuki Страницы: 526

Бренд: Honda Страницы: 330

Бренд: R&G Страницы: 9

Бренд: Hama Страницы: 22

Бренд: Parkside Страницы: 24

Бренд: Parkside Страницы: 109

Бренд: AGUSTA Страницы: 427

Бренд: Dynajet Страницы: 20

Бренд: VESPA Страницы: 82

Spyder ST Limited SE5

Бренд: Can-Am Страницы: 41

Бренд: Vetter Страницы: 11

Бренд: Yamaha Страницы: 66

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды