CAMSO CTS Скачать руководство пользователя страница 17 | Manualshive

Страница: 17 / 20

CAMSO CTS Скачать руководство пользователя страница 17

CPB-435CNH Case and New Holland Combines (without speed multiplier)

Camso | 04-17 | 17

23. Identify if the combine has axle extensions

installed or not. Combine axle extensions are a
factory option when purchasing a combine.
Although, a large portion of the combines in
North America have the axle extensions, it is
still important to verify that the combine has the
axle extensions installed to determine best
installation of the CTS track systems.

24. Install the track system onto the combine axle. Take care that the front of the track is on

the tensioning cylinder side.

a. Combines with axle extensions already installed.

No additional changes are required and CTS
should be bolted directly (with the addition of the
spacer plate included in the fitment kit) to the
combine axle. Install spacer plate onto the axle
hub.

NOTE:

The wheel studs are not used when

mounting the CTS to the combine axle. Only the
thru bolts from the CTS drivewheel and threading
directly into the axle housing are used. These
bolts are supplied with the fitment kit.

b. Combines without axle extensions installed.

i. Preferred CTS Installation

•

Install Axle Extensions onto

combine. Please contact your
local dealer for parts and
instructions to install the axle
extensions.

ii. Recommended CTS Installation

(without axle extensions)

•

Bolt CTS directly to axle (with

addition of the spacer plate
included in the fitment kit).

•

Minor modifications to the

combine will be required in
order for the track to clear.

Combine

Axle

Extension

«
...
15
16
17
18
19
...
»

Содержание CTS





















Отзывы:

Нет отзывов