manualshive.com logo in svg

CAMSO CTS, Инструкция по установке

Поделиться
Скачать
CAMSO CTS Скачать руководство пользователя страница 14

 

CPB-435CNH Case and New Holland Combines (without speed multiplier)  

Camso |  04-17  |  14  

 

14. Connect Oscillation Limiters to the CTS track 

frame using the clevis. 

 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

WARNING

 

Install original or backup protections and the ladder in conformity with the 
safety rules before starting up the engine. 
 

 

WARNING

 

The rubber track has the possibility to move transversally ¼ - ½ in (8-10 
mm) each side. Verify that clearance between the track and the combine 
harvester body is suitable in all pivoting positions of the track. 

15.

 

Drive machine around for 5 
minutes. Recheck mounting bolt 
torque. Mounting bolts should be 
torqued to 500 ft-lbs (670 Nm).

 

Repeat process until no 
additional bolt rotational 
movement occurs.

 

 
 
 
 
 
 
 
 
 

 

16. After 1 hour of use, retorque mounting bolts to 500 ft-lbs (670 Nm). Repeat hourly check 

until no further bolt rotational movement occurs. 

 

 

WARNING

 

•

  It is important to follow the installation instructions and to use a 

calibrated torque wrench to ensure bolts are properly torqued. Failure 
to do so may result in the CTS mounting bolts coming loose and the 
bolts breaking resulting in downtime and possible damage to the 
combine and CTS. 

 

Содержание CTS





















Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды