4. Handle the appliance with care. Do not drop it.
MODEL No.
&0
-T2
%87$1(
GAS TORCH
INSTRUCTIONS FOR USE
IMPORTANT:
Read these instructions for use carefully so as to familiarize yourself with
the appliance before connecting it to its gas cartridge.
Keep these instructions for future reference.
NAME OF PARTS
1. Check that seals between the appliance and the gas cartridge are in place
and in good condition before connecting to the gas cartridge. (Fig. 1) O-ring
shall be fitted in the inlet port of the valve.
2. Do not use the appliance if it has damaged or worn seals; Do not use an
appliance which is leaking, damaged or which does not operate properly.
3
3. This appliance must be used in a well-ventilated location in accordance with
national requirements for the supply of combustion air (minimum ventilation
required 5m /h) and to avoid the dangerous building up of un-burnt gases.
4. The appliance shall be used away from flammable materials and on
minimum distance from adjacent surfaces (wall, ceiling);
rear 60cm – Side 60cm – Ceiling 100cm
5. Gas cartridge shall be changed in a well-ventilated location, preferably
outside, away from any sources of ignition, such as naked flames, pilots,
electric fires and away from other people.
6. If there is a leak on your appliance (smell of gas), take it outside immediately
into a well-ventilated flame free location where the leak may be detected and stopped.
INTRODUCTION
If you wish to check for leaks on your appliance, do it outside. Do not try to detect
leaks using a flame, use soapy water.
1. CAUTION: accessible parts may become very hot. Keep young children
away from the appliance.
2. Storage: Always store the appliance after removing the gas cartridge in a safe
cool dry place when it is not use.
3. Do not misuse the appliance, or use it for anything for which it has not been designed.
Fig.2
Fig.1
'O' ring seals
OFF
Fig.4
START/ ON
1
Fig.3
1
Twist 35
2
Tab
2
PUSH
3. In event of any problem, please contact the dealer.
ASSEMBLING THE APPLIANCE
1. Make sure the control knob (1) is fully closed (by turning it clockwise as far as it will go). (Fig.2)
2. Keep the gas cartridge upright when fitting it to the valve.
3. Align the notch in the collar of the gas cartridge with the locator tab (2) on the valve
adaptor (3) of the appliance.
4. Push down the valve adaptor gently in the concave part of the gas cartridge and turn the gas
cartridge clockwise until “hand tightened”. (Fig.3)
5. If the gas cartridge is not connected correctly, you will hear a hissing sound. Ensure that a
complete gas seal has been made. If you wish to check for leaks on your appliance, do it outside.
Do not try to detect leaks using a flame, use soapy water. Any leakage will show up as bubbles
around leakage area. If you are in doubt or you can hear or smell gas, do not attempt to light the
appliance. Remove gas cartridge from the appliance and contact your local dealer.
OPERATING THE APPLIANCE
1. Turn the control knob anticlockwise and pull the trigger (4) until you hear a click indicating that
a spark has been produced. (Fig. 4)
2. Adjust the size of the flame by turning the control knob.
3. Be careful the phenomenon of flaring which may occur during the warm up period and if the
appliance is moved. The appliance can be used without flaring after 30 seconds of warm-up period.
4. After use, ensure the control knob is turned fully clockwise. (Fig.2)
5. Turn the gas cartridge counter-clockwise from the valve body to disconnect. Then store the
appliance and gas cartridge separately.
CHANGING THE GAS CARTRIDGE
1. Check that the cartridge is empty before changing it (shake to hear the noise made by
the liquid)
2. Check that flame is extinguished before disconnecting the gas cartridge.
3. When the appliance is cool turn the gas cartridge counterclockwise from the valve adaptor to
disconnect.
4. Check the seals before connecting a new gas cartridge to the appliance.
5. Change the gas cartridge outside and away from people.
6. For safe connection of the gas cartridge, check all joints and couplings of the valve adaptor
periodically to insure against loose connection.
ROUTINE MAINTENANCE
1. Always ensure that the sealing O-ring is in place and in good condition. If it is damaged or
worn, replace it.
2. Before connecting the gas cartridge, make sure that the position of tap and joints of the valve
adaptor is as the following illustration.
GENERAL MAINTENANCE AND REPAIRS
1. Do not modify the appliance.
Before connecting
gas cartridge
After connecting
gas cartridge
HANDLING THE APPLIANCE
Valve Adaptor
3
Ignition Trigger
4
Burner Tube (Spout)
5
Control Knob
1
Locator Tab
2
Hanger
6
This appliance shall only be used with the
&59
butane cartridge
&0
/
&07
CRV.
It may be hazardous to attempt to fit other types of gas cartridges.
Injector size 0.23 mm
Nominal rate: 65 g/h / 3.2 Mj/hr
SAFETY IFORMATION
7. Carbon monoxide hazard-using this appliance in an enclosed space
may cause death. Do not use in caravans, tents, marine craft, cars, mobile
Homes or similar locations.
2. This appliance must only be serviced by an authorized person.
