background image

WARRANTY AND ASSISTANCE

The following warranty applies to the

 

SDM1502 COMMUNICATION INTERFACEPS1502B POWER

CONTROL MODULE, and the SDMX50 50 OHM COAX MULTIPLEXER.

These products are warranted by CAMPBELL SCIENTIFIC, INC. to be free from defects in materials and
workmanship under normal use and service for twelve (12) months from date of shipment unless specified
otherwise.  Batteries have no warranty.  CAMPBELL SCIENTIFIC, INC.'s obligation under this warranty is
limited to repairing or replacing (at CAMPBELL SCIENTIFIC, INC.'s option) defective products.  The
customer shall assume all costs of removing, reinstalling, and shipping defective products to CAMPBELL
SCIENTIFIC, INC.  CAMPBELL SCIENTIFIC, INC. will return such products by surface carrier prepaid.
This warranty shall not apply to any CAMPBELL SCIENTIFIC, INC. products which have been subjected
to modification, misuse, neglect, accidents of nature, or shipping damage.  This warranty is in lieu of all
other warranties, expressed or implied, including warranties of merchantability or fitness for a particular
purpose.  CAMPBELL SCIENTIFIC, INC. is not liable for special, indirect, incidental, or consequential
damages.

Products may not be returned without prior authorization.  To obtain a Returned Materials Authorization
(RMA), contact CAMPBELL SCIENTIFIC, INC., phone (435) 753-2342.  After an applications engineer
determines the nature of the problem, an RMA number will be issued.  Please write this number clearly on
the outside of the shipping container.  CAMPBELL SCIENTIFIC's shipping address is:

CAMPBELL SCIENTIFIC, INC.
RMA#_____
815 West 1800 North
Logan, Utah 84321-1784

CAMPBELL SCIENTIFIC, INC. does not accept collect calls.

Non-warranty products returned for repair should be accompanied by a purchase order to cover the repair.

815 W.  1800 N.
Logan, UT 84321-1784
USA
Phone  (435) 753-2342
FAX  (435) 750-9540
www.campbellsci.com

Campbell Scientific Canada Corp.
11564 -149th Street
Edmonton, Alberta T5M 1W7
CANADA
Phone  (403) 454-2505
FAX  (403) 454-2655

Campbell Scientific Ltd.
Campbell Park
80 Hathern Road
Shepshed, Leics. LE12 9RP
ENGLAND
Phone  (44)-50960-1141
FAX  (44)-50960-1091

Содержание PS1502B















Отзывы: