background image

Warranty and Assistance 

The

 

HUB-SDM5 

is warranted by CAMPBELL SCIENTIFIC, INC. to be free 

from defects in materials and workmanship under normal use and service for 
twelve (12) months from date of shipment unless specified otherwise.  
Batteries have no warranty.  CAMPBELL SCIENTIFIC, INC.'s obligation 
under this warranty is limited to repairing or replacing (at CAMPBELL 
SCIENTIFIC, INC.'s option) defective products.  The customer shall assume 
all costs of removing, reinstalling, and shipping defective products to 
CAMPBELL SCIENTIFIC, INC.  CAMPBELL SCIENTIFIC, INC. will 
return such products by surface carrier prepaid.  This warranty shall not apply 
to any CAMPBELL SCIENTIFIC, INC. products which have been subjected 
to modification, misuse, neglect, accidents of nature, or shipping damage.  This 
warranty is in lieu of all other warranties, expressed or implied, including 
warranties of merchantability or fitness for a particular purpose.  CAMPBELL 
SCIENTIFIC, INC. is not liable for special, indirect, incidental, or 
consequential damages. 

Products may not be returned without prior authorization.  The following 
contact information is for US and International customers residing in countries 
served by Campbell Scientific, Inc. directly.  Affiliate companies handle 
repairs for customers within their territories.  Please visit 
www.campbellsci.com to determine which Campbell Scientific company 
serves your country.  To obtain a Returned Materials Authorization (RMA), 
contact CAMPBELL SCIENTIFIC, INC., phone (435) 753-2342.  After an 
applications engineer determines the nature of the problem, an RMA number 
will be issued.  Please write this number clearly on the outside of the shipping 
container.  CAMPBELL SCIENTIFIC's shipping address is: 

 

 

CAMPBELL SCIENTIFIC, INC. 

 RMA#_____ 
 

815 West 1800 North 

 

Logan, Utah 84321-1784 

 

CAMPBELL SCIENTIFIC, INC. does not accept collect calls. 

 

 

 

Содержание HUB-SDM5











Отзывы: