Campbell GRANITE VOLT 108 Скачать руководство пользователя страница 19 | Manualshive

Страница: 19 / 62

background image

in blue. The VOLT 108 has 16 SE terminals, and the VOLT 116 has 32. For example, single-ended
channel 1 is comprised of terminals 1 and

⏚

.

7.1.1.2 Differential measurements

A differential measurement measures the difference in voltage between two input terminals. Use
a differential measurement to measure current by using external resistors to convert current to
voltage. The VOLT 108 has 8 H/L differential terminals, and the VOLT 116 has 16.

7.1.1.3 Period averaging

Single-ended terminals on the VOLT 100 series are also configurable for measuring the period of
an analog signal.

l

Voltage gain: 1, 3.8, 19, 67

l

Maximum frequency: 200 kHz

l

Resolution: 130 ns ÷ number of cycles to be measured

7.1.2 Voltage and current excitation

X terminals supply switched voltage or current to sensors. The VOLT 108 has two X terminals, and
the VOLT 116 has four.

l

Voltage Excitation (switched-analog output) – X terminals, configured for voltage
excitation output, supply precise voltage in the range of ±5000 mV. These terminals are
regularly used with resistive-bridge measurements. Each terminal will source up to ±50 mA.

l

Current Excitation (switched-analog output) – X terminals, configured for current excitation
output, supply precise current in the range of ±2.5 mA. These terminals are regularly used
with resistive-bridge measurements.

7.1.3 Switched voltage output

SW5V and SW12V terminals supply voltage and control for sensors. The VOLT 108 includes two
SW5V and one SW12V terminals. The VOLT 116 includes four SW5V and two SW12V terminals.

l

5 V control – SW5V terminals supply 5000 mV. See

(p. 20) for information

on voltage and current sourcing limits.

l

Switched 12 V – SW12V terminals supply 12 V and will source up to 200 mA each.

VOLT 100 series

12

«
...
17
18
19
20
21
...
»

Содержание GRANITE VOLT 108































































Отзывы:

Нет отзывов

Похожие инструкции для GRANITE VOLT 108

615 Series ANSI

Бренд: ABB Страницы: 60

Бренд: Eaton Страницы: 166

Бренд: Walimex Pro Страницы: 68

Бренд: Jabra Страницы: 4

Бренд: Nabco Страницы: 35

Бренд: KaRo Страницы: 12

Бренд: York Страницы: 24

Бренд: Zamel Страницы: 23

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 2

Бренд: Zander Aachen Страницы: 44

Extra Free ROB-01/12-24V

Бренд: Zamel Страницы: 2

Бренд: Zamel Страницы: 14

Бренд: Paser Страницы: 2

Бренд: Computer Automation Technology Страницы: 55

Бренд: KATO VISION Страницы: 23

Бренд: Paradox Страницы: 28

TallyMan TMCP 16

Бренд: TSL Страницы: 26

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды