manualshive.com logo in svg

Campbell ET107, Инструкция по эксплуатации, Страница: 5 / 110

Поделиться
Скачать
Campbell ET107 Скачать руководство пользователя страница 5

ET107 Weather Station Table of Contents 

Appendices 

A.  ET107 Maintenance Log

......................................... A-1 

B.  PS24 24 Ahr Power Supply and 10 x 12 inch  

Enclosure

............................................................ B-1 

B.1  PS24 Components................................................................................B-1 
B.2  Installation............................................................................................B-4 

C.  Exploded Views

....................................................... C-1 

C.1  Enclosure..............................................................................................C-1 
C.2  Crossarm ..............................................................................................C-2 

D.  Default Programs

.................................................... D-1 

D.1  Program for ET107 with Gill WindSonic........................................... D-1 
D.2  Program for ET107 with 034B ........................................................... D-4 

Figures 

1.1-1.  Effect of Structure on Wind Flow .................................................... 1-2 
1.2-1A.  Cut Flap Packing Tape .................................................................. 1-3 
1.2-1B.  Shipping Box Packaging ............................................................... 1-3 
1.2-2.  ET107 with the Met One 034B-ETM Wind Sensor, Top Layer ...... 1-4 
1.2-3.  ET107, Bottom Layer....................................................................... 1-4 
1.5-1.  Magnetic Declination for the Contiguous United States .................. 1-7 
1.5-2.  Declination Angles East of True North Are 

Subtracted From 0 to Get True North........................................... 1-9 

1.5-3.  Declination Angles West of True North Are 

Added to 0 to Get True North....................................................... 1-9 

2.1-1.  ET Tower Installation....................................................................... 2-1 
2.1-2.  ET Tower Base Installation.............................................................. 2-3 
2.1-3.  Cut-Away View Shows Anchor Bolt and Conduit Placement in  

Cement Pad................................................................................... 2-3 

2.2-1.  Transparent View Shows Raising and Grounding the ET Tower .... 2-5 
2.2-2.  Close up of Ground Rod and 4 AWG Cable .................................... 2-6 
2.3-1.  ET107 Instrumentation Mounted on the ET Tower ......................... 2-7 
2.3-2.  Enclosure Spacing Above Pole ........................................................ 2-8 
2.4-1.  ET107 Sensor Arm Mounting .......................................................... 2-9 
2.4-2.  Temperature/Relative Humidity Sensor with Yellow  

Protective Cap ............................................................................ 2-10 

2.4-3.  Temperature/Relative Humidity Sensor without Yellow  

Protective Cap ............................................................................ 2-11 

2.4-4.  Wind and RH/Temperature Sensor Installation ............................. 2-12 
2.4-5.  034B Mounting to Pipe .................................................................. 2-12 
2.4-6.  Screws that Secure the Electronics Cover ...................................... 2-14 
2.4-7.  Removal of the Electronics Cover.................................................. 2-14 
2.4-8.  Jumper Set for WindSonic1 ........................................................... 2-15 
2.4-9.  Gill WindSonic Mounting Shaft..................................................... 2-16 
2.4-10. Gill WindSonic Connected to Cable ............................................. 2-16 
2.4-11.  Remove Rubber Band from Tipping Mechanism......................... 2-17 

iii 

Содержание ET107















































































































Отзывы:

Нет отзывов