background image

EC155 CO

2

 and H

2

O Closed-Path Gas Analyzer 

22 

Do not connect or disconnect the EC155 gas analyzer head 

or CSAT3 sonic head while the EC100 is powered. 

1.

 

Connect the EC155 gas analyzer head. Begin by removing the black 

rubber cable entry plug on the bottom right of the EC100 enclosure. (This 

plug can be stored in the mesh pocket of the enclosure). Now insert the 

cable entry plug that is attached to the large cable of the EC155 gas 

analyzer head into the vacant slot. Push the connector at the end of the 

cable onto its mating connector (labeled 

Gas Analyzer

) and tighten the 

thumbscrews (see FIGURE 

6-12

). The EC155 gas analyzer cable is 

approximately 3 m (9.8 ft) in length. 

2.

 

Connect the EC155 sample cell cable. Unscrew the sample cell connector 

cover, which is found on the bottom of the EC100 enclosure. Insert the 12-

prong sample cell cable connector into the female connector on the 

enclosure and screw it firmly in place. The EC155 sample cell cable is 

approximately 3 m (9.8 ft) in length.  

3.

 

Connect the CSAT3A sonic head (skip this step if not using the CSAT3A). 

Similar to (a), begin by removing the black rubber cable entry plug found 

on the bottom left of the EC100 enclosure. Insert the cable entry plug on 

the CSAT3A cable into the slot and connect the male end to the female 

connector labeled 

Sonic Anemometer

 on the EC100 electronics (see 

FIGURE 

6-13

). Tighten the thumbscrews. The CSAT3A cable is 

approximately 3 m (9.8 ft) in length. 

 

FIGURE 6-13.  Connection for CSAT3A in EC100 module 

CAUTION 

Sonic Anemometer 

Connector of EC100 

Содержание EC155































































































Отзывы: