Campbell COM111 Скачать руководство пользователя страница 67 | Manualshive

Страница: 67 / 72

Campbell COM111 Скачать руководство пользователя страница 67

D-

1

Appendix D. Using the COM111 in
Transparent GSM Dial-up mode

It is possible to use the COM111 in transparent mode, when the default non-transparent
(RLP) mode is not supported by the cellular phone network or is incompatible with the
COM111.

D.1 Introduction

The COM111 software includes an advanced error correction protocol known as
RLP, which is specially designed for RF links. This protocol is now used in one
form or another by most GSM data units but the COM111 implementation of RLP
may not be compatible with all GSM networks and some networks do not support
this mode at all.

If you find that the  COM111 does not work on the network and
suspect that it may be due to the RLP protocol, you must check
carefully with your own network provider to see if the COM111
implementation  of  the  protocol  is  known  to  work  correctly  on
their  network.  Also  check  the  modem  has  been  configured  to
connect in 2G Modem Mode Only.

The transparent mode relies on Loggernet/PC400W to correct any communication
errors. On poor quality lines the PC software will often drop the call and redial
when it sees a certain level of errors. (The non-transparent mode is less prone to
doing this.) For successful and fast communication a signal strength (as reported
by AT+CSQ – see Appendix C) of 18 or above is recommended for transparent
mode. The non-transparent mode will operate at signal levels down to as low as
10.

D.2 Disabling the RLP Protocol

If you wish to use the COM111 in transparent mode, do the following:

1.

Get your SIM card in the COM111 enabled for transparent mode. In some
cases you may have to call your airtime provider to do this, (e.g. UK O2 where
you will be allocated a new number for this mode) while others (such as UK
Vodafone) need no configuration on the network and will switch automatically
depending on the COM111 configuration.

2.

Configure the modem for GSM dial-up using the Mobile Data Assistant
package, but afterwards using the Advanced mode to enter a revised setting
using the command AT+CBST=7,0,0 (where the last digit, 0, switches the unit
to transparent mode).

3. Save the settings using the AT&W command as normal.

NOTE

«
...
65
66
67
68
69
...
»

Содержание COM111









































































Отзывы:

Нет отзывов