Campbell CMP10 Скачать руководство пользователя страница 6

Страница: 6 / 42

Table of Contents

B.3

Example Program for Measuring a CMP21 ..................................... B-3

CVF4 Ventilation Unit ............................................ C-1

C.1

General Information ......................................................................... C-1

C.2

CVF4 Components ........................................................................... C-1

C.3

CVF4 Installation ............................................................................. C-3

C.4

Wiring .............................................................................................. C-7

C.4.1

Schematics ................................................................................ C-8

C.5

CVF4 Example Program .................................................................. C-9

C.6

CVF4 Heater/Ventilator Maintenance ............................................ C-11

Figures

6-1. Dimensions ...........................................................................................5

7-1. Pyranometer installation .......................................................................8

7-2. Pyranometer mounted horizontally for the Northern Hemisphere

(left) and Southern Hemisphere (right) .............................................8

7-3. Two views of a pyranometer mounted at an angle for the Northern

Hemisphere .......................................................................................9

7-4. Pyranometer mounted at an angle for the Southern Hemisphere .........9

7-5. Exploded view of the pyranometer .................................................... 11

7-6. Thermopile detector schematic .......................................................... 11

8-1. Reading is reduced if dome is not dry or clean .................................. 16

8-2. Changing the desiccant ...................................................................... 16

C-1. CVF4 Components (top view, no cover) .......................................... C-2

C-2. CVF4 Components (bottom view) ................................................... C-2

C-3. CVF4 Ventilation Unit and Ships With Kit ..................................... C-3

C-4. Crossarm and Nu-Rail Crossover Fitting Mounted to Mast

(exploded view) ............................................................................ C-4

C-5. CM220 Right-Angle Mounting Bracket attached to

CM200-series crossarm ................................................................ C-4

C-6. Mounting CVF4 feet to a mounting stand ........................................ C-5

C-7. Mounting the pyranometer to the CVF4 .......................................... C-5

C-8. CVF4 Mounted to CVF4 Mounting Stand (pyranometer not

shown) .......................................................................................... C-6

C-9. 8-Pin Schematic ............................................................................... C-8

C-10. 4-Pin Schematic ............................................................................... C-9

C-11. CVF4 filter replacement ................................................................. C-12

Tables

5-1. Model Comparison ...............................................................................4

6-1. CMP-series Specifications ...................................................................6

7-1. CMP6, CMP10, and CMP11 Wire Color, Function, and Data

Logger Connection ......................................................................... 12

7-2. CMP21 Wire Color, Function, and Data Logger Connection ............ 12

7-3. Multipliers Required for Flux Density and Total Fluxes ................... 14

B-1. CR1000X Wiring for CMP6 Example Program .............................. B-1

B-2. CR1000X Wiring for CMP10/CMP11 Example Program ............... B-2

B-3. CR1000X Wiring for CMP21 Example Program ............................ B-3

C-1. CVF4 8-Pin Wiring .......................................................................... C-7

C-2. CVF4 4-Pin Wiring .......................................................................... C-7

C-3. Wiring for Program Controlling CVF4 Heater ................................ C-9

Содержание CMP10










































Результаты поиска

Содержание CMP10

Отзывы:

Бренды по названию

Популярные бренды

Campbell CMP10, Руководство по эксплуатации продукта

Результаты поиска

Содержание CMP10

Отзывы:

Бренды по названию

Популярные бренды