manualshive.com logo in svg

Campbell CM106BK, Руководство по эксплуатации продукта

Поделиться
Скачать
Campbell CM106BK Скачать руководство пользователя страница 14

CM106BK Tripod Kit 

8 

5.

 

Attach each leg assembly to the tripod body using two 5/16-18 x 2.00 in. 

bolts and lock nuts. Do not over-tighten the bolts. The tripod legs and leg 

braces must be able to pivot. 

 

5.2  Tripod Base Positioning 

Tripod installation near power lines is dangerous. The 

minimum safe recommended distance from overhead 

power lines is 1 1/2 times the height of the tripod and 

mast combined. Call your local utility providers to 

locate buried utilities prior to installation. 

The tripod base has three legs, which are individually adjustable, that allow the 

tripod to be installed over non-level terrain. 

Prepare the area where the tripod will be installed. The tripod requires an area 

approximately 3.4 m (11 ft) in diameter. Natural vegetation and the ground 

surface should be disturbed as little as possible, but brush and tall weeds should 

be removed. 

Stand the tripod base up on end, and rotate the feet perpendicular to the legs. 

Each leg has a clamp bracket with a bolt that locks the leg in place when 

tightened.  

WARNING 

Содержание CM106BK



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды