Campbell CD295 Скачать руководство пользователя страница 5

Страница: 5 / 32

DataView II (CD295) Dual Line Display

While in sleep mode the DataView II will continue to respond to PakBus

communications, however the LCD is turned off and no requests are sent to the

data logger.

2. Installation Procedure

Below is a general guide to the steps involved in configuring and programming

a DataView II (CD295).

Download the latest version of the CD295 OS,

PC295W

, and the

Device

Configuration Utility

from

www.campbellsci.com/downloads

Connect the 9-pin D-connector of the programming cable into the CD295

data cable and the other end into your computer serial COM port.

Using

PC295W

and the data logger program, configure your screens of

your DataView II (DV2 file).

Using

Device Configuration Utility

, send the DataView II program (DV2

file), and change any settings (e.g., PakBus Address).

Remove the programming cable.

Mount the CD295 into your data logger enclosure.

Connect the CD295 data cable to the data logger RS-232 port.

Power up the data logger and CD295 and verify correct operation.

3. Software

3.1 Computer System Requirements

3.1.1 Minimum Configuration

PENTIUM-class machine with 64 MB RAM running Windows 98.

3.1.2 Recommended Configuration

PENTIUM-class machine with 128 MB RAM running Windows 2000/XP.

3.2 Software Installation

To begin the installation of the

PC295W

software, download the latest

version of the software from

www.campbellsci.com/downloads

and open

the setup.exe file, which contains the software to be used.

Содержание CD295
































Результаты поиска

Содержание CD295

Отзывы:

Бренды по названию

Популярные бренды

Campbell CD295, Руководство по эксплуатации продукта

Результаты поиска

Содержание CD295

Отзывы:

Бренды по названию

Популярные бренды