![background image](http://html.mh-extra.com/html/campbell-hausfeld/ironforcfe-wl6500-series/ironforcfe-wl6500-series_operating-instructions-manual_489649021.webp)
Funcionamiento
(Continuacíon)
PERILLA DEL REGULADOR
1. Esta perilla controla el aire comprimido
que se le suministra a las herramientas
neumáticas o pistolas pulverizadoras.
2. Gire la perilla en el mismo sentido de
las agujas del reloj para aumentar la
presión de aire suminstrado.
3. Gire la perilla en sentido contrario al de
las agujas del reloj para disminuir la
presión de aire suministrado.
4. Gire la perilla completamente en
sentido contrario a las agujas del reloj
para cerrar el suministro de aire
completamente.
MANOMETRO PARA MEDIR LA
PRESION DE SALIDA
(HERRAMIENTA)
1. Este manómetro le
permite verificar la presión
de salida muy fácilmente.
Esta presión se mide en
barras.
2. Cerciórese de que el
manómetro esté en CERO
antes de cambiar de
herramientas neumáticas
o desconectar la
manguera.
21 Sp
Mantenimiento
MANOMETRO DEL TANQUE
Mide la presión del tanque
para verificar que el sistema
está funcionando
adecuadamente.
Desconecte el cordón eléctrico del
tomacorrientes y libere toda la presión del
sistema antes de tratar de instalar, darle
servicio, cambiar de lugar o darle
cualquier tipo de mantenimiento.
Este compresor se debe chequear con
frecuencia para ver si tiene algún tipo de
problemas y le debe dar el siguiente
mantenimiento antes de cada uso.
1. Hále el anillo de la válvula de seguridad
y deje que calce en su posición normal.
!
ADVERTENCIA
Debe
reempla-
zar la válvula de seguridad si no la puede
activar o si hay fugas de aire una vez que
haya soltado el anillo.
2. Coloque la unidad en posición
horizontal como indicado en la
Figura 8. Apague el compresor y libere
toda la presión, después: Abra la llave
de drenaje, ubicada debajo del tanque,
para drenarle toda la humedad.
3. APAGUE la unidad y limpie la tapa
del cabezal, el tanque y las líneas de
aire.
IMPORTANTE:
Debe colocar el com-
presor lo más lejos posible del área de
trabajo, según lo permita la longitudud
de la manguera, para evitar que el filtro
se atasque.
LUBRICACION
Este compresor no requiere lubricación.
ALMACENAMIENTO
1. Mientras no lo esté usando debe
almacenar el compresor y las
mangueras en un sitio seco y frío.
2. Debe drenar el tanque.
3. Debe desconectar las mangueras y
colgarlas con los extremos hacia abajo
para que se drenen.
!
ADVERTENCIA
Serie WL6500
4
Operation
Pressure Switch
- Auto/Off Switch - In
the
ON
position, the compressor shuts
off automatically when tank pressure
reaches the maximum preset pressure.
The compressor will automatically
restart when it reaches the minimum
preset pressure. In the
OFF
position,
the compressor will not operate. This
switch should be in the
OFF
position
when connecting or disconnecting the
power cord from the electrical outlet
or when changing air tools.
Regulator
- The regulator controls the
amount of air pressure released at the
hose outlet.
ASME Safety Valve
- This valve
automatically releases air if the tank
pressure exceeds the preset maximum.
Handle
- Designed to move the
compressor.
Tool Storage
- 1/4 inch quick connect
couplers fit in holes to support air
chuck and other inflation fittings.
Never use the
handle on wheeled
units to lift the unit completely off the
ground.
!
WARNING
Drain Petcock
- This valve is located on
the bottom of the tank. Use this valve
to drain moisture from the tank daily
to reduce the risk of corrosion.
Reduce tank pressure below 10 PSI,
then drain moisture from tank daily to
avoid tank corrosion. Drain moisture
from tank(s) by opening the drain
petcock located underneath the tank.
LUBRICATION
This is an oilless product and
DOES
NOT
require lubrication to operate.
IMPORTANT:
Do not operate compres-
sor before reading instructions or
damage may result.
1. Turn switch to OFF position and plug
in power cord.
2. Attach chuck or other tool to open
end of hose.
3. Turn regulator clockwise to open air
flow.
4. Turn switch to ON position.
5. Compressor will build to maximum
preset pressure and shut off.
6. Adjust regulator to proper pressure
for tool or tire. Operate tool per
instructions. Compressor will
automatically restart when pressure
in tank drops below cut-in pressure.
7. Turn regulator knob counterclock-
wise to shut off the air and turn
switch to Off position.
In the ON position, the compressor
pumps air into the tank. It shuts off
automatically when unit reaches its
maximum preset pressure. In the OFF
position, the compressor will not
operate. This switch should be in the
OFF position when connecting or
disconnecting the power cord from the
electrical outlet.
ASME SAFETY VALVE
Do not remove or
attempt to adjust
the safety valve!
This valve should be checked under
pressure occasionally by pulling the ring
by hand. If air leaks after ring has been
released, or valve is stuck and cannot be
actuated by ring, it MUST be replaced.
REGULATOR KNOB
1. This knob controls air pressure to an
air operated tool, or paint spray gun.
2. Turning knob clockwise increases air
pressure at outlet.
3. Turning counterclockwise will lower
air pressure at outlet.
4. Fully counterclockwise will shut off
flow of air completely.
OUTLET (TOOL) PRESSURE GAUGE
1. This gauge shows at-a-
glance, air pressure at
outlet. Air pressure is
measured in pounds
per square inch (psi).
2. Be sure this gauge reads ZERO before
changing air tools or disconnecting
hose from outlet.
TANK PRESSURE GAUGE
Gauge shows pressure in
tank indicating
compressor is building
pressure properly.
Disconnect power source
then release all pressure
from the system before
attempting to install,
service, relocate or perform any
maintenance.
!
WARNING
!
WARNING
MOISTURE IN COMPRESSED AIR
Moisture in compressed air will
form into droplets as it comes from
an air compressor pump. When
humidity is high or when a
compressor is in continuous use for
an extended period of time, this
moisture will collect in the tank.
When using a paint spray or
sandblast gun, this water will be
carried from the tank through the
hose, and out of the gun as
droplets mixed with the spray
material.
IMPORTANT:
This condensation
will cause water spots in a paint
job, especially when spraying other
than water based paints. If
sandblasting, it will cause the sand
to cake and clog the gun,
rendering it ineffective. A filter in
the air line (MP3105), located as
near to the gun as possible, will
help eliminate this moisture.
Oilless Compressors
Notas
Figure 7
bar
bar
www.chpower.com
Figure 6
Tank
Pressure
gauge
Regulator
Tool
Pressure
gauge
Figura 8