![background image](http://html.mh-extra.com/html/campbell-hausfeld/chn10510/chn10510_operating-instructions-manual_489817006.webp)
symptom
Possible Cause(s)
Corrective action
Air leaking at trigger valve
area .
O-Rings in trigger valve housing are
damaged
Replace o-rings
Air leaking between housing
and nose .
1 . Damaged o-rings
1 . Replace o-rings
2 . Damage to bumper
2 . Replace bumper
Air leaking between housing
and cap .
1 . Loose screws
1 . Tighten screws
2 . Damaged seal
2 . Replace seal
Tool skips driving fastener
1 . Worn bumper
1 . Replace bumper
2 . Dirt in nose piece
2 . Clean drive channel
3 . Dirt or damage prevent fasteners or
pusher from moving freely in magazine
3 . Clean magazine
4 . Damaged pusher spring
4 . Replace spring
5 . Inadequate air flow to tool
5 . Check fitting, hose, or compressor
6 . Worn o-rings on piston or lack of
lubrication
6 . Replace and lubricate o-rings
7 . Damaged o-rings on trigger valve
7 . Replace o-rings
8 . Air leaks
8 . Tighten screws and fittings
9 . Cap seal leaking
9 . Replace seal
10 . Defect in automatic nail length plate
10 . Clear problem with plate
Tool runs slow or has loss of
power
1 . Tool not lubricated sufficiently
1 . Lubricate nailer
2 . Broken spring in cylinder cap
2 . Replace spring
3 . Exhaust port in cap is blocked
3 . Replace damaged internal parts
Fasteners are jammed in tool 1 . Guide on driver is worn
1 . Replace guide
2 . Fasteners are not correct size
2 . Use only recommended fasteners
3 . Fasteners are bent
3 . Replace with undamaged fasteners
4 . Magazine or nose screws are loose
4 . Tighten screws
5 . Driver is damaged
5 . Replace driver
Troubleshooting Chart
Stop using tool immediately if any of the following problems occur. Serious personal injury could occur.
Any repairs or replacements must be done by a Qualified Service Person or Authorized Service Center.
6
Operating Instructions
UsEr-MaiNTENaNCE
iNsTrUCTioNs (CoNTiNUED)
To maximize the life of the blade,
closely examine fasteners for defects .
Do not use defective or improper
fasteners . Also load fasteners in the
proper orientation; the pin points and
the arrows always point toward the
wood surface . Drive fasteners into wood
products only (see "Loading/ Unloading
The Nailer") .
Even with good care, extended use
of the tool may eventually lead to tip
failure . Replacement driver assemblies
can be purchased by calling 1-800-
543-6400 and refer to part number
SKN24000AV .
Replace assembly by first removing the
four (4) head cap screws using the 4mm
hex wrench provided . Remove head cap
and components to access the driver
piston . Remove and replace driver
assembly using your fingers . Replace
components and head cap as removed .
assEMblY ProCEDUrE for sEals
When repairing a tool, the internal
parts must be cleaned and lubricated .
Parker O-lube or equivalent must be
used on all o-rings . Each o-ring must be
coated with O-lube before assembling .
A small amount of oil must be used on
all moving surfaces and pivots . After
reassembling, a few drops of 30W
non-detergent oil or equivalent, must
be added through the air line before
testing .
sToraGE
The tool should be stored in a cool dry
place .
interchange information
Can use 3/8 inch to 1 inch pins from the
following branded 23 g micropinners:
Senco FP10, Air Locker P630, Porter
Cable PIN100, Grex P635, and Max
NF235A .
www.chpower.com
Содержание CHN10510
Страница 7: ...7 CHN10510 Notes www chpower com ...