manualshive.com logo in svg

Cameron W-K-M 370D5, Инструкция по установке, эксплуатации и обслуживанию

Поделиться
Скачать
Cameron W-K-M 370D5 Скачать руководство пользователя страница 5

5

IOM-WKM-BALL-370D5

DISTRIBUTED VALVES

TC9186

3. Install in line; either end may be installed upstream.
4. Install vent valve, if not already factory-installed.
5. On valves having extensions, check all extension piping and fittings to ensure that 

all are tight prior to placing valve in service.

6. The seat sealant system is intended only for emergency shut-off. Do not lube. 

(See Section III-C).

III. ON STREAM MAINTENANCE 

This part covers maintenance and repair which can be performed without removing the valve 
from the line.

A. BLOCK-AND-BLEED

With the line under pressure the valve body cavity can be vented to atmosphere and com-
pletely drained down with the ball in the 

CLOSED POSITION ONLY

.

The valve body cavity may be drained and flushed by: 

1. Removing the special vent valve after pressure has been vented.
2. Removing the 1/2” NPT relief valve from the upper body area.
3. Flushing through upper relief valve connection and allowing drainage through the 

lower vent plug connection.

 

 

D I S T R I B U T E D   V A L V E S  

 

Installation, Operation and Maintenance Manual 

4 

W-K-M 370D5

 

 

 

 

 

 

 

B. STEM SEAL O-RING REPLACEMENT 

NOTE: ON NEWER VERSIONS OF THE 370D5 BALL 

VALVE,  THE ADAPTER PLATE AND STOP 

COLLAR ARE ONE-PIECE. (SEE FIG. A & B, 

PAGE 4) 

* On newer valves a needle valve is supplied in lieu of 
a vent plug. 
The 370D5 has two stem seals, one primary seal, backed up 
by a second independent seal. 
If the primary O-Ring seal becomes faulty, a leak will 
occur through the gland plate vent plug.* In this case 
remove 1/4" vent plug* and replace with 1/4" solid plug 
to energize the secondary O-Ring seal. 

1. To verify the integrity of the primary stem seal, 

open the needle on the vent assembly plug.* 
If the primary seal is faulty, close the needle valve 
to energize the secondary seal. 

KEY STOP 

1991 - 

 

 

FIG. A 

 

FIG. B 

1.

 

  STEM 

1.  STEM 

2.

 

  KEY 

2.  KEY 

3.

 

  ADAPTER PLATE 

3.  ADAPTER PLATE 

4.

 

  STOP COLLAR 

 

 

5.

 

  NYLON WASHER 

 

 

6.

 

  STOP CAPSCREW 

 

 

NOTE: 

OLDER VALVES 

HAVE A DOUBLE 

BALL CHECK AND 

GREASE FITTING. 

BALL CHECK & 

GREASE 

FITTING 

SPECIAL 

VENT PLUG 

BODY RELIEF 

VALVE 

NOTE: 

DIFFERENT TYPE 

VENT PLUGS OR DRAIN 

VALVES MAY BE SUPPLIED. 

STOP COLLAR 

1963 - 1990 

STEM 

GLAND 
BUSHING 

ADAPTER PLATE 

1/4" NPT 

DRILLED PLUG.* 
LEAKAGE 
INDICATES 
FAILURE OF 
PRIMARY 
STEM SEAL 

PRIMARY 

STEM SEAL 

GLAND PLATE 

UPPER THRUST WASHER 

LINE 

PRESSURE 

 

5 

6 

1 

2 

1 

2 

3 

3 

4 

 

 

D I S T R I B U T E D   V A L V E S  

 

Installation, Operation and Maintenance Manual 

4 

W-K-M 370D5

 

 

 

 

 

 

 

B. STEM SEAL O-RING REPLACEMENT 

NOTE: ON NEWER VERSIONS OF THE 370D5 BALL 

VALVE,  THE ADAPTER PLATE AND STOP 

COLLAR ARE ONE-PIECE. (SEE FIG. A & B, 

PAGE 4) 

* On newer valves a needle valve is supplied in lieu of 
a vent plug. 
The 370D5 has two stem seals, one primary seal, backed up 
by a second independent seal. 
If the primary O-Ring seal becomes faulty, a leak will 
occur through the gland plate vent plug.* In this case 
remove 1/4" vent plug* and replace with 1/4" solid plug 
to energize the secondary O-Ring seal. 

1. To verify the integrity of the primary stem seal, 

open the needle on the vent assembly plug.* 
If the primary seal is faulty, close the needle valve 
to energize the secondary seal. 

KEY STOP 

1991 - 

 

 

FIG. A 

 

FIG. B 

1.

 

  STEM 

1.  STEM 

2.

 

  KEY 

2.  KEY 

3.

 

  ADAPTER PLATE 

3.  ADAPTER PLATE 

4.

 

  STOP COLLAR 

 

 

5.

 

  NYLON WASHER 

 

 

6.

 

  STOP CAPSCREW 

 

 

NOTE: 

OLDER VALVES 

HAVE A DOUBLE 

BALL CHECK AND 

GREASE FITTING. 

BALL CHECK & 

GREASE 

FITTING 

SPECIAL 

VENT PLUG 

BODY RELIEF 

VALVE 

NOTE: 

DIFFERENT TYPE 

VENT PLUGS OR DRAIN 

VALVES MAY BE SUPPLIED. 

STOP COLLAR 

1963 - 1990 

STEM 

GLAND 
BUSHING 

ADAPTER PLATE 

1/4" NPT 

DRILLED PLUG.* 
LEAKAGE 
INDICATES 
FAILURE OF 
PRIMARY 
STEM SEAL 

PRIMARY 

STEM SEAL 

GLAND PLATE 

UPPER THRUST WASHER 

LINE 

PRESSURE 

 

5 

6 

1 

2 

1 

2 

3 

3 

4 

Содержание W-K-M 370D5



























Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды