manualshive.com logo in svg

CAME ZLX24S, Инструкция по эксплуатации

Поделиться
Скачать
CAME ZLX24S Скачать руководство пользователя страница 20

  

20

  - Manual 

FA01797-EN - 

 05/2022 -  © CAME S.p.A. - The contents of this manual may be changed at any time and without notice. -  Translation of the original instructions

Confi guration >

Motor settings

Motor power

Minimum power [up to 120W]
Medium power (Default) [up to 200W]
Maximum power [more than 200W]

Confi guration >

Motor settings

Confi gure motor M1

Motor type
Encoder
Limit-switch function
Input type FC/FA
Motor power

 See the specifi c parameters for each function.

Confi guration >

Motor settings

Confi gure motor M2

Motor type
Encoder
Limit-switch function
Input type FC/FA
Motor power

 See the specifi c parameters for each function.

Confi guration >

Gate travel settings

Opening speed

40% to 100% (Default 70%)

Confi guration >

Gate travel settings

Closing speed

40% to 100% (Default 70%)

Confi guration >

Gate travel settings

Travel AST control

Deactivated (Default)

 Maximum thrust and low obstruction 

sensitivity.

Minimum
Average
Maximum*

(*) Minimum thrust and high obstruction 
sensitivity.

Customised
Customised closing
Customised opening

Confi guration >

Gate travel settings

Adjusting the partial opening

10% to 100% (Default 100%)

Confi guration >

Gate travel settings

Opening approach space

0.5% to 25.0% (Default 8.0%)

Confi guration >

Gate travel settings

Closing approach space

0.5% to 25.0% (Default 8.0%)

Содержание ZLX24S

































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды