The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
Pa
g.
8
- M
anu
al c
od
e:
3
1
9
319
L
R
LR
1
6
ve
r.
1
.0
1.
0
0
2
/2
0
0
8 © C
A
M
E c
an
celli auto
mati
ci
s.p
.a.
ENGLISH
-Connect the antenna’s RG58 cable to the apposite terminals.
-Lock the radiofrequency card into the electronic card
D
AFTER CUTTING OFF THE POWER SUPPLY (or after disconnecting the batteries).
N.B.: the electronic card only recognises the radiofrequency card when the power is on.
Activating the remote control
-Keep the “
PROG
”
A
button on the electronic card pressed. The LED fl ashes.
B
-Press the transmitter button you wish to memorise. The LED will stay on to show memorisation has been successful.
Selecting functions
E
1 ON
Automatic closing function activated; (1 OFF-deactivated);
2 ON
“Open” function with activated remote control (HF board inserted);
2 OFF
“Open-close-reverse” function with pushbutton (2-7) and activated remote control (HF board inserted) ;
3 ON
“Maintained Action” function (remote control function disabled) activated; (3 OFF deactivated);
4 ON
Activated pre-fl ashing during opening and closing,, with device connected on terminals 10- E6 (4 OFF deactivated);
5 ON
Obstacle detection. With the motor off (bar closed, open or after a total-stop command), movement is blocked if safety devices
(e.g. photoelectric cells) detect an obstacle;
6 OFF
Total stop function activated, connect pushbutton to 1-2 (if not set the dipswitch to ON);
7 OFF
Reopening function during closure activated, connect the safety devices to terminals 2-C1 (if not used set the dipswitch to ON);
8 ON
Safety test function to check photoelectric cell effi ciency (page.7) activated; (8 OFF deactivated).
9 OFF
Encoder activated for obstacle detection (9 ON deactivated);
10 ON
Activates the intermittence function during movement - device hooked up to 10-E6.
10 OFF
Activates the intermittence function when bar is closed - device hooked up to 10-E6.
Memorizing the code on the command board
The data and information reported in this installation manual are susceptible to change at any time and without obligation on CAME cancelli automatici s.p.a. to notify users.
Pa
g.
8
- M
anu
al c
od
e:
3
1
9
319
L
R
LR
1
6
ve
r.
1
.0
1.
0
0
2
/2
0
0
8 © C
A
M
E c
an
celli auto
mati
ci
s.p
.a.
ENGLISH
-Connect the antenna’s RG58 cable to the apposite terminals.
-Lock the radiofrequency card into the electronic card
D
AFTER CUTTING OFF THE POWER SUPPLY (or after disconnecting the batteries).
N.B.: the electronic card only recognises the radiofrequency card when the power is on.
Activating the remote control
-Keep the “
PROG
”
A
button on the electronic card pressed. The LED fl ashes.
B
-Press the transmitter button you wish to memorise. The LED will stay on to show memorisation has been successful.
Selecting functions
E
1 ON
Automatic closing function activated; (1 OFF-deactivated);
2 ON
“Open” function with activated remote control (HF board inserted);
2 OFF
“Open-close-reverse” function with pushbutton (2-7) and activated remote control (HF board inserted) ;
3 ON
“Maintained Action” function (remote control function disabled) activated; (3 OFF deactivated);
4 ON
Activated pre-fl ashing during opening and closing,, with device connected on terminals 10- E6 (4 OFF deactivated);
5 ON
Obstacle detection. With the motor off (bar closed, open or after a total-stop command), movement is blocked if safety devices
(e.g. photoelectric cells) detect an obstacle;
6 OFF
Total stop function activated, connect pushbutton to 1-2 (if not set the dipswitch to ON);
7 OFF
Reopening function during closure activated, connect the safety devices to terminals 2-C1 (if not used set the dipswitch to ON);
8 ON
Safety test function to check photoelectric cell effi ciency (page.7) activated; (8 OFF deactivated).
9 OFF
Encoder activated for obstacle detection (9 ON deactivated);
10 ON
Activates the intermittence function during movement - device hooked up to 10-E6.
10 OFF
Activates the intermittence function when bar is closed - device hooked up to 10-E6.
Memorizing the code on the command board
