CAME VER10DMS, Руководство пользователя, Страница: 31 / 112

P
age
3
- Manual
FA01768-EN
- 07/2022 - © C
AME S.p.A. - The contents of this manual may be changed at any time and without notice. - T
ranslation of the o
riginal instructions
GENERAL PRECAUTIONS FOR INSTALLERS
Important safety instructions.
Please follow all of these instructions. Improper installation may cause serious bodily harm.
Before continuing, please also read the general precautions for users.
Only use this product for its intended purpose. Any other use is hazardous. • The manufacturer cannot be held liable for
any damage caused by improper, unreasonable or erroneous use. • This product is defined by the Machinery Directive
(2006/42/EC) as partly completed machinery. • Partly completed machinery means an assembly which is almost
machinery but which cannot in itself perform a specific application. • Partly completed machinery is only intended to be
incorporated into or assembled with other machinery or other partly completed machinery or equipment thereby forming
machinery to which the Machinery Directive (2006/42/EC) applies. • The final installation must comply with the Machinery
Directive (2006/42/EC) and the European reference standards in force. • The manufacturer declines any liability for using
non-original products, which would also void the warranty. • All operations indicated in this manual must be carried out
exclusively by skilled and qualified personnel and in full compliance with the regulations in force. • The device must be
installed, wired, connected and tested according to good professional practice, in compliance with the standards and
laws in force. • Make sure the mains power supply is disconnected during all installation procedures. • Check that the
temperature ranges given are suitable for the installation site. • Do not install the operator on surfaces that could yield and
bend. If necessary, add suitable reinforcements to the anchoring points. • Make sure you have set up a suitable dual-
pole cut-off device along the power supply that is compliant with the installation rules. It should completely cut off the
power supply according to category III surcharge conditions. • Demarcate the entire site properly to prevent unauthorised
personnel from entering, especially minors. • In case of manual handling, have one person for every 20 kg that needs
hoisting; for non-manual handling, use proper hoisting equipment in safe conditions. • Use suitable protection to prevent
any mechanical hazards due to persons loitering within the operating range of the operator. • The electrical cables must
pass through special pipes, ducts and cable glands in order to guarantee adequate protection against mechanical damage.
• The electrical cables must not touch any parts that may overheat during use (such as the motor and transformer). •
Before installation, check that the guided part is in good mechanical condition, and that it opens and closes correctly. •
Remove all cords and chains and disable any equipment not required for automating the guided part such as locks. • The
product cannot be used to automate any guided part that includes a pedestrian gate, unless it can only be enabled when
the pedestrian gate is secured. • The operator must not be used with guided parts that have openings exceeding 50 mm
in diameter, or that have protruding edges/parts someone could grab or stand on. • Make sure that nobody can become
trapped between the guided and fixed parts, when the guided part is set in motion. • All fixed controls must be clearly
visible after installation, in a position that allows the guided part to be directly visible, but far away from moving parts.
All fixed controls must be installed at least 1.5 m above the floor. • Where operated with a hold-to-run control, install a
STOP button to disconnect the main power supply to the operator, to block movement of the guided part. • Install the
manual release device below 1.8 m. If the manual release device is removable, store it somewhere near the operator. • If
not already present, apply a permanent tag that describes how to use the manual release mechanism close to it. • Make
sure that the operator has been properly adjusted and that the safety and protection devices and the manual release are
working properly. Check that the operator inverts the motion when the guided part comes into contact with an object 50
mm tall positioned on the pavement. • Following installation, ensure that the guided part does not extend onto any public
footpaths or roads. • Before handing over to the final user, check that the system complies with the harmonised standards
and the essential requirements of the Machinery Directive (2006/42/EC).