p.
2
- M
an
u
al c
od
e:
11
9
G
U
4
0
11
9
G
U
4
0
v.
1
1
2
/2
0
14 © C
A
M
E C
an
ce
lli A
uto
m
ati
ci S
.p.
A
. - T
h
e d
ata a
n
d i
nf
or
m
ati
on i
n th
is m
an
u
al m
ay b
e c
h
an
g
ed at a
ny ti
m
e a
n
d w
ith
ou
t n
ot
ic
e fr
om
C
A
M
E C
an
ce
lli
A
uto
m
ati
ci
S
.p.
A
.
Danger of hand crushing
Danger! High voltage.
No transiting while the barrier is moving
Premise
• Employ this product only for the use for which it was expressly made. Any
other use is dangerous. CAME Cancelli Automatici S.p.A is not liable for any
damage caused by improper, wrongful and unreasonable use • The safety
of this product and its proper fi tting depends, therefore, on respecting its
technical characteristics and proper fi tting, to be done in state-of-the-art
fashion, and under safe conditions as expressly explained in the literature that
comes with the product. • Keep these warnings together with the installation
and operation manuals that come with the operator.
Before installing
(checking what's there: if something is missing, do not continue until you
have complied with all safety provisions)
• Fitting and testing must be be only performed by qualifi ed technicians • Laying
the cables, installation and testing mus follow state-of-the-art procedures as
dictated by regulations • Before beginning any operation it is mandatory to
carefully read all instruction; improper installation may result in serious harm
to people and things • Make sure the boom is in good mechanical state,
balanced and aligned, and that it opens and closes properly. Also, if needed,
fi t suitable protections o use proper safety sensors • If the operator is to be
installed at a height of over 2.5 m from the ground or other access level, make
sure you have any necessary protections and/or warnings in place • If any
pedestrian openings are fi tted into the operator, there must also be a a system
to block their opening while they are moving • Make sure that the opening
automatic barrier cannot entrap people against the fi xed parts of the operator
• Do not install the operator upside down or onto elements that could yield
and bend. If necessary, add suitable reinforcements to the anchoring points
• Do not install on tilted surfaces • Make sure the temperature range shown
on the product literature is suitable to the climate where it will be installed as
explained in the manual.
Installing
• Suitably section off and demarcate the entire installation site to prevent
unauthorized persons from entering the area, especially minors and children
• Be careful when handling operators that weigh over 20 kg. If need be, use
proper safety hoisting equipment • The CE-marked safety devices (photocells,
stepping plates, sensitive safety-edges, emergency buttons, and so on), must
be fi tted in compliance with the regulations in eff ect and according to state-
of-the-art criteria, taking into account the environment, the type of required
service and of the working forces applied to moving leaves. Any shearing
or conveying points must be sensor-protected • Any residual risks must be
pointed out to end users and highlighted with pictograms as provided by the
law. • All opening commands (that is, buttons, key switches, magnetic readers,
and so on) must be installed at least 1.85 m from the perimeter of the barrier's
working area, or where they cannot be reached from outside the barrier. Also,
any direct commands (buttons, touch panels, and so on) must be installed
at least 1.5 m from the ground and must not be reachable by unauthorized
persons • The automatic barrier must visibly show its identifi cation data. •
Before connecting the main power supply make sure that the identifi cation
data correspond to the those of the network • The automatic barrier must be
connected to an eff ective regulation grounding system.
• The manufacturer declines any liability for using non-original products;
which would result in warranty loss • All maintained action commands, must
be fi tted in places from which the moving barrier and transit and driving areas
are visible • Apply, if missing, a permanent sign showing the position of the
release device • Before delivering to the users, make sure the system is EN
12453 and EN 12445 standard compliant (regarding impact forces), and
also make sure the system has been properly adjusted and that any safety,
protection and manual release devices are working properly • Apply Warning
Signs where necessary and in a visible place (such as the gate's license plate)
Special user-instructions and recommendations
• Keep barrier operation areas clean and free of any obstructions. Make sure
the photocell's operating fi eld is clear of any obstructions • Do not allow
children to play with fi xed commands, or to loiter in the barrier's maneuvering
area. Keep any remote control transmitters or any other command device
away from children, to prevent the operator from being accidentally activated
• The apparatus may be used by children of eight years and above and by
physically, mentally and perceptively challenged people, or even ones without
any experience, provided this happens under close supervision or once they
have been properly instructed to use the apparatus safely and to the potential
hazards involved. Children must not play with the apparatus. Cleaning and
maintenance by users must not be done by children, unless properly supervised
• Frequently check the system for any malfunctions or signs of wear and tear
or damage to the moving structures, to the component parts, all anchoring
points, including cables and any accessible connections. Keep any hinges,
moving joints and slide rails properly lubricated • Perform functional checks
on the photocells and sensitive safety edges, every six months. Constantly
clean the photocells' glass covers using a slightly water-moistened cloth; do
not use any solvents or other chemical products that may ruin the devices • If
repairs or modifi cations are required to the system, release the operator and
do not use it until safety conditions have been restored • Cut off the power
supply before releasing the operator for manual openings and before any other
operation, to prevent potentially hazardous situations. Read the instructions •
f the power supply cable is damaged, it must be replaced by the manufacturer
or authorized technical assistance service, or in any case, by similarly qualifi ed
persons, to prevent any risk • It is FORBIDDEN for users to perform any
OPERATIONS THAT ARE NOT EXPRESSLY REQUIRED OF THEM AND WHICH ARE
NOT LISTED in the manuals. For any repairs, modifi cations and adjustments
and for extra-ordinary maintenance, CALL TECHNICAL ASSISTANCE • Log the
job and checks into the periodic maintenance log.
Further recommendations for all
• Keep away from and do not loiter near the barrier and mechanical moving
parts • Do not enter the barrier's area of operation when it is moving • Do not
counter the operator's movement as this could result in dangerous situations
• Always pay special attention to any dangerous points, which have to be
labeled with specifi c pictograms and/or black and yellow stripes • When using
a selector switch or a command in maintained actions, keep checking that
there are no persons within the operating range of any moving parts, until the
command is released • The barrier may move at any time and without warning
• Always cut off the power supply before performing any maintenance or
cleaning.
WARNING!
important safety instructions for people:
READ CAREFULLY!
