CAME 001G4040EZT, Руководство по установке

Страница: 51 / 128

p.
1
9
19
- M
an
u
al
c
od
e:
F
A
0
0
5
8
3
-E
N
FA
0
0
5
8
3
-E
N
v.
1 1
10
/2
0
1
6 - © C
am
e S
.p.
A
. T
h
e c
onte
nts of th
is
m
an
u
al
m
ay b
e c
h
an
g
ed at a
ny ti
m
e w
ith
ou
t p
rio
r n
oti
ce
.
F1 Total stop [1-2]
0 = Deactivated (
default
) / 1 = Activated
NC input - Barrier stops while excluding any automatic closing; to resume movement, use the control device. The safety device is inserted into
[1-2].
F2 Input [2-CX]
0 = Deactivated (
default
) / 1 = C1 / 4 = C4 / 5 = C5 / 9 = C9
NC input – Can associate: C1 = reopening during closing by photocells, C2 = reclosing during opening by photocells, C3 = partial stop, C4 =
obstruction wait, C5 = immediate closing, C9 = immediate closing with obstruction wait during closing.
F3 Input [2-CY]
0 = Deactivated (
default
) / 1 = C1 / 4 = C4 / 5 = C5 / 9 = C9
NC input – Can associate: C1 = reopening during closing by photocells, C2 = reclosing during opening by photocells, C3 = partial stop, C4 =
obstruction wait, C5 = immediate closing, C9 = immediate closing with obstruction wait during closing.
F5 Safety test
0 = Deactivated (
default
) / 1 = CX / 2 = CY / 3 = CX+CY
After every opening or closing command, the board will check whether the photocells are working properly.
 IMPORTANT! IMPORTANT! Start programming by first performing the following: A1 BOOM-TYPE SETTING, A2
MOTOR TEST, F1 TOTAL STOP and A3 CALIBRATING BOOM TRAVEL.
Functions menu
F 1 Total stop function (1-2)
F 2 Function associated to input CX
F 3 Function associated to input CY
F 5 Safety test function
F 6 Maintained action function
F 9 Obstruction detection with motor idle function
F 10 Function associated the open-barrier signal output
F11 Exclude Encoder
F 14 Sensor type selection function
F 15 Intermittent luminous cord function
F 18 Additional light function
F 19 Automatic closing time
F 21 Preflashing time
F 22 Working time
F 25 Courtesy light time
F 28 Adjusting opening speed
F 29 Adjusting closing speed
F 30 Adjusting opening slow-down speed
F 31 Adjusting closing slow-down speed
F 33 Adjusting calibration speed
F 34 Sensitivity during travel
F 35 Sensitivity during slow-downs
F 37 Adjusting the opening slow-down starting point
F 38 Adjusting the closing slow-down starting point
F 49 Manage serial connection
F 50 Save data in memory roll
F 51 Reading memory roll data
F 52 Copying parameters from Master to Slave
F 56 Number of the peripheral
F 60 Sleep Mode function
F 61 Pre-flashing function
F 63 Changing COM speed
U 1 Enter new user with an associated command
U 2 Delete single user
U 3 Deleting all users
A 1 Boom-type setting
A 2 Motor test
A 3 Travel calibration
A 4 Resetting parameters
A 5 Counting maneuvers
H 1 Software version
Functions map