Camco 26 dB Скачать руководство пользователя страница 3

IMPORT

ANT SAFET

Y INSTRUCTIONS

USER MANUAL

VORTEX 6, 4, 2.6 and 200V

P.2

IMPORTANT SAFETY INSTRUCTIONS

1) Read the information for use (user manual).

2) Please keep this user manual in a safe place during the lifetime of the am-

plifi er. The user manual forms an integral part of the amplifi er. Reselling of the 

amplifi er is only possible if the user manual is available. Any changes made to 

the amplifi er have to be documented in writing and passed on to the buyer in 

the event of resale.

3) Heed all warnings.

4) Follow all instructions.

5)Do not use this amplifi er near water (for example, in damp rooms or near a 

swimming pool). Do not place any object fi lled with liquids, such a vase, on the 

amplifi er.

6) Clean only with dry cloth.

7) Do not block any ventilation openings. Install in accordance with the user 

manual.

8) Do not install near any heat sources such as radiators, heat registers, stoves, or 

other apparatus that produce heat.

9) Protect the power cord from being walked on, pinched or damaged in any 

other way. Pay particular attention to plugs and the point where they exit from 

the amplifi er.

10) The amplifi er may only be used in accordance with the information provided 

in the user manual. Before and during the usage of the amplifi er please ensure 

that all recommendations, especially the safety recommendations as detailed in 

the user manual, are adhered to.

The 

VORTEX

-Amplifi er is designed for the amplifi cation of pulsed audio signals 

and the amplifi er should only be connected to speakers with an average 

impedance that is not lower than the impedances specifi ed in points 

3.9.2, 3.9.3 

and 

3.9.4.

11) Do not place this amplifi er on an unstable cart, stand, 

tripod, bracket, or table. The device may fall, causing 

serious injury, and serious damage to the device itself.

12) The amplifi er can only be disconnected from the power supply by removing 

the plug, which must be freely accessible at all times.  Unplug this amplifi er 

during lightning storms or when unused for long periods of time.

13) Refer all servicing to qualifi ed service personnel. 

Servicing is required when  

   the power-supply cord or plug has been damaged, 

   liquid has been spilled or objects have fallen into the amplifi er, 

   the amplifi er has been exposed to rain or moisture, 

   the amplifi er has been dropped or suffered damage in any other way,

    the amplifi er exhibits a distinct change from its normal function or 

performance.

Содержание 26 dB









































Отзывы: