CAMBRIDGE Qt Conference Room Edition Скачать руководство пользователя | Manualshive

Страница: 9 / 23

background image

page 16

Qt Conference Room Edition Installation and Operations Guide

INSTALLATION

8.

Run the cable to next designated tile specified on emitter layout and wiring diagram. Tie cables up

to structure or suspend from deck as required by local building code.

9.

On the next emitter, connect this cable to the INPUT jack.

10.

Repeat Steps 4 through 9 for the remaining emitters on the home run.

Set sound masking volume levels using either the front panel controls.

DO NOT put the input cable into the output port of the emitter. If sound is only heard by putting the

cable in the output, there is a problem earlier in the cable run. Be sure to fix any problems and hear the

“whooshing” sound before installing the next emitter.

The input jack of each emitter bears this symbol
and is located near the safety tie off

The output jack of each emitter bears this symbol

Note:

«
...
7
8
9
10
11
...
»

Содержание Qt Conference Room Edition
























Отзывы:

Нет отзывов

Похожие инструкции для Qt Conference Room Edition

Бренд: ABB Страницы: 138

Бренд: ABB Страницы: 116

Ascotel Office 45

Бренд: Aastra Страницы: 40

Бренд: Aastra Страницы: 244

Бренд: Aastra Страницы: 30

Бренд: Aastra Страницы: 24

IntelliGate A150

Бренд: Aastra Страницы: 524

Ascotel IntelliGate 150

Бренд: Aastra Страницы: 228

Бренд: Aastra Страницы: 22

Бренд: Yamaha Страницы: 4

Бренд: Zeck Audio Страницы: 16

Бренд: Audipack Страницы: 12

Бренд: Skov Страницы: 68

Бренд: ATEN Страницы: 176

Бренд: Siku Страницы: 150

Бренд: Japan Radio Co. Страницы: 101

Бренд: Hama Страницы: 76

Бренд: ITC Страницы: 15

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды