Cambium Networks PMP 450 Series Скачать руководство пользователя

Страница: 76 / 292

Chapter 2: System hardware

AC+DC Enhanced Pow er Inject or C0 0 0 0 65L0 0 2C

The AC+DC Enhanced Power Injector interfaces are shown in AC+DC Enhanced Power Injector interfaces
and described in AC+DC Enhanced Power Injector interface functions.

Figure 17 :

AC+DC Enhanced Power Injector interfaces

Table 47 :AC+DC Enhanced Power Injector interface functions

Interface

Function

100- 240V 47-
63Hz 1.7A

AC power input (main supply)

DC In

Alternative DC power supply input

DC Out

DC power output to a second PSU (for power supply redundancy) or to a NIDU

ODU

RJ45 socket for connecting Cat5e cable to ODU

LAN

RJ45 socket for connecting Cat5e cable to network

Power - AC

Indicates power is applied at the AC power input

Содержание PMP 450 Series





































































































































































































































































































Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды

Cambium Networks PMP 450 Series, Руководство по установке

Результаты поиска

Содержание PMP 450 Series

Отзывы:

Похожие инструкции для PMP 450 Series

Бренды по названию

Популярные бренды