Cambium Networks PMP 450 Series Скачать руководство пользователя | Manualshive

Страница: 74 / 292

background image

Chapter 2: System hardware

74

Pow er sup p ly – PMP 4 50 m Ser ies

The PMP 450m Series - 5 GHz AP supports powering from the following power sources:

l

AC+DC Enhanced Power Injector (see AC+DC Enhanced Power Injector C000065L002C)

l

CMM5 56 V power and sync injector module with external 240 W or 600 W power supply

PSU part numbers

Table 44 :PSU part numbers for PMP 450m AP (5/3 GHz)

AP
Model

Cambium description

Cambium part number

5 GHz

AC+DC Enhanced Power
Injector

C000065L002C

3 GHz

Power Supply, AC, 54 V 240 W

N000000L054B

Pow er sup p ly – PMP/ PTP 4 50 i Ser ies

The PMP/PTP 450i Series supports powering from the following powering sources:

l

Power Supply, 60 W, 56 V with 1000BASE-T or GigE

l

AC+DC Enhanced Power Injector

l

Power over Ethernet midspan, 60 W, -48 V DC Input

l

CMM4 with external 56 V power supply and CMM4 to 450i Series ODU cable (Dongle)

l

CMM5 56 V power and sync injector module with external 240 W or 600 W power supply

l

IEEE802.3at power injector

Note

The 900 MHz SM is based off of the 450 Series , please see Power supply –
PMP/PTP 450 Series .

Warning

Always use an appropriately rated and approved AC supply cord-set in
accordance with the regulations of the country of use.

Warning

The PMP 450 Ruggedized High Gain Integrated Subscriber Module (Cambium
part numbers C035045C014A and C036045C014A), while encapsulated in a
450i-type enclosure, contains 450 circuitry which must be powered via 30 V
DC. Powering these SMs with a 56 V DC will damage the device.

Please refer to PMP 450 MicroPoP AP for details on maximum cable lengths between power injector and
PMP/PTP 450i.

«
...
72
73
74
75
76
...
»

Содержание PMP 450 Series





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PMP 450 Series

Бренд: H3C Страницы: 42

Бренд: BEC Страницы: 18

Barricade SMC7004VWBR V.2

Бренд: SMC Networks Страницы: 82

Бренд: Y!mobile Страницы: 2

Бренд: Deliberant Страницы: 69

ZoneFlex series

Бренд: Ruckus Wireless Страницы: 68

Бренд: H3C Страницы: 34

Бренд: sauter Страницы: 8

Бренд: RadioLabs Страницы: 9

Бренд: NEBRA Страницы: 10

Бренд: Encore Страницы: 25

Бренд: Encore Страницы: 62

Бренд: Aruba Networks Страницы: 2

Бренд: D-Link Страницы: 159

OfficeConnect OC20

Бренд: HPE Страницы: 4

Бренд: HPE Страницы: 4

Бренд: Nortel Страницы: 26

Бренд: Quectel Страницы: 57

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды