Cambium Networks PMP 450 Series Скачать руководство пользователя | Manualshive

Страница: 200 / 292

background image

Chapter 5: Installation

200

Chap t er 5: Inst allat ion

This chapter describes how to install and test the hardware for a 450 Platform link. It contains the
following topics:

l

ODU variants and mounting bracket options provides details of six different bracket options,
including the type of ODU and range of pole diameters supported by each option.

l

Mount the ODU, LPU and surge suppressor describes how to mount and ground an integrated or
connectorized ODU, how to mount and ground the top LPU.

l

Installing the copper Cat5e Ethernet interface describes how to install the copper Cat5e power
over Ethernet interface from the ODU to the PSU.

l

Installing external antennas to a connectorized ODU describes how to install external antennas for a
connectorized ODU.

l

Installing ODU describes how to install PTP and PMP ODU radios.

l

Installing the AC Power Injector describes how to install a power supply unit for the PMP/PTP 450
platform, either the AC Power Injector.

l

Supplemental installation information contains detailed installation procedures that are not
included in the above topics, such as how to strip cables, create grounding points and
weatherproof connectors.

Note

These instructions assume that LPUs are being installed from the 450 Platform
Family LPU and grounding kit (Cambium part number C000065L007). If the
installation does not require LPUs, adapt these instructions as appropriate.

If LPUs are being installed, only use the five black-capped EMC cable glands
supplied in the LPU and grounding kit. The silver-capped cable glands supplied in
the ODU kits must only be used in 450 Platform installations which do not require
LPUs.

ODU v ariant s and m o unt ing b racket o p t io ns

Mount ing bracket – PMP/ PTP 4 50 i Series

The PMP/PTP 450i Series supports below mentioned mounting bracket option:

Table 123 :PMP/PTP 450i Series - ODU mounting bracket part numbers

Cambium description

Cambium part number

Mounting bracket – low profile adjustable

N000045L002A

The low-profile bracket provides elevation adjustment with the PMP/PTP 450i Series Integrated ODUs of
+10° to –5° or +5° to –10°. A larger adjustment range is available using the standard integrated mounting
bracket. The connectorized mounting bracket does not provide elevation adjustment.

«
...
198
199
200
201
202
...
»

Содержание PMP 450 Series





































































































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для PMP 450 Series

Бренд: Watchguard Страницы: 26

DGL-4500 - GamerLounge Xtreme N Gaming Router...

Бренд: D-Link Страницы: 108

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Бренд: D-Link Страницы: 38

DAP-3520 - AirPremier N Dual Band Exterior PoE Access...

Бренд: D-Link Страницы: 80

DAP-2590 - AirPremier N Dual Band PoE Access...

Бренд: D-Link Страницы: 36

Бренд: TRENDnet Страницы: 2

OfficeConnect 3CRWDR100B-72

Бренд: 3Com Страницы: 118

Бренд: Advantek Networks Страницы: 62

Бренд: Edimax Страницы: 15

Бренд: MeshLinx Страницы: 94

Бренд: TP-Link Страницы: 35

Бренд: Z-Com Страницы: 18

Бренд: EnGenius Страницы: 117

Бренд: Aztech Страницы: 20

Бренд: IP-COM Страницы: 15

Бренд: IP-COM Страницы: 63

Бренд: Zte Страницы: 32

BLUESOCKET 3040

Бренд: ADTRAN Страницы: 6

Бренды по названию

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Популярные бренды

Загрузить еще бренды