manualshive.com logo in svg

Cambium Networks cnWave V1000, Быстрый старт

Поделиться
Скачать
Cambium Networks cnWave V1000 Скачать руководство пользователя страница 7

Product Safety Information

7

Product Safety Information

Warning

To prevent loss of life or physical injury, observe the following safety guidelines.
In no event shall Cambium Networks be liable for any injury or damage caused
during the installation of the Cambium 60 GHz cnWave™ radio nodes. Ensure that
only qualified personnel install 60 GHz cnWave™ radios.

Attention

Pour éviter toute perte de vie ou blessure physique, respectez les consignes de
sécurité suivantes. En aucun cas Cambium Networks ne pourra être tenu
responsable des blessures ou dommages causés lors de l'installation des nœuds
radio Cambium 60 GHz cnWave ™. Assurez-vous que seul du personnel qualifié
installe les radios cnWave ™ 60 GHz.

1. Exercise extreme care when working near power lines.

2. Exercise extreme care when working at heights.

3. Always use one of the approved power supply options. Failure to use the Cambium-supplied PSUs

could result in equipment damage and will invalidate the safety certification and may cause a safety
hazard.

4. The cnWave™ radios must be properly grounded to protect against lightning. It is the user’s

responsibility to install the equipment in accordance with national regulations. In the USA, follow the
requirements of the National Electrical Code NFPA 70-2005 and 780-2004 Installation of Lightning
Protection Systems. In Canada, follow Section 54 of the Canadian Electrical Code. These codes
describe correct installation procedures for grounding the outdoor unit, mast, lead-in wire and
discharge unit, size of grounding conductors and connection requirements for grounding
electrodes. Other regulations may apply in different countries and therefore it is recommended that
installation of the outdoor unit be contracted to a professional installer.

5. Always use an appropriately rated and approved AC supply cord-set in accordance with the

regulations of the country of use.

6. Before servicing 60 GHz cnWave™ equipment, always switch off the power supply and unplug it

from the PSU. Do not disconnect the RJ45 drop cable connectors from the radio while the PSU is
connected to the power supply. Always remove the AC or DC input power from the PSU.

7. The main power supply is the primary disconnect device.

8. Safety may be compromised if outdoor- rated cables are not used for connections that will be

exposed to the outdoor environment.

9. The PSU output voltage may be hazardous in some conditions, for example in wet weather. Do not

connect a drop cable tester to the PSU, either directly or via LPUs.

10. Strong radio frequency (RF) fields will be present close to the antenna when the transmitter is on.

Always turn off the power to the radio before undertaking maintenance activities in front of the

Содержание cnWave V1000



































Отзывы:

Нет отзывов

Бренды по названию

Популярные бренды

Загрузить еще бренды