Cambium Networks cnPilot R200 Скачать руководство пользователя страница 17

Страница: 17 / 151

Chapter 2: Basic Settings

Hardware Installation

Page

Chapter 2:

Basic Settings

This chapter covers:

•

Web Management Interface

•

Accessing and Configuring cnPilot Home Router via cnMaestro

•

Configuring via Voice Commands

Web Management Interface

cnPilot Home Routers feature a web browser-based interface that may be used to configure and
manage the device. See below for information.

Note
By default, http access is disabled. Only https is allowed.

Logging in from the LAN port

Ensure your PC is connected to the router’s LAN port correctly.

Note
You may either set up your PC to get an IP dynamically from the router or set up the
IP address of the PC to be the same subnet as the default IP address of router is
192.168.11.1. For detailed information, see

Chapter 4:

Troubleshooting Guide.

EZ UI

cnPilot Home Routers provides an additional simplified management interface for home users. The

home users can connect to any of the LAN port of the device and access the EZ UI by entering

https://mywifi.net

in the browser.

Home users needs to provide the default Basic User credentials as useradmin/admin.

Note
Please check with your ISP in case the Basic User credentials have been changed
for improved security.

Figure 3 EZ UI

Содержание cnPilot R200
























































































































































Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды

Cambium Networks cnPilot R200, Руководство пользователя

Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды