Cambium Networks cnPilot R200 Скачать руководство пользователя страница 116

Страница: 116 / 151

Chapter 3: Advanced Configuration

Administration

Page

114

Firmware Upgrade

Table 73 Firmware upgrade

Description

Choose upgrade file type from Image File and Dial Rule

Press “Browse” button to browse the file

Press

to start upgrading

Provision

Provisioning allows cnPilot Home Router to auto-upgrade and auto-configure devices which
support TFTP, HTTP and HTTPs .

•

Before testing or using TFTP, user should have tftp server and upgrading file and configuring
file.

•

Before testing or using HTTP, user should have http server and upgrading file and configuring
file.

•

Before testing or using HTTPS, user should have https server and upgrading file and
configuring file and CA Certificate file (should same as https server’s) and Client Certificate file
and Private key file

User can upload a CA Certificate file and Client Certificate file and Private Key file in the Security
page.

Содержание cnPilot R200
























































































































































Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды

Cambium Networks cnPilot R200, Руководство пользователя

Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды