Cambium Networks cnPilot R200 Скачать руководство пользователя страница 112

Страница: 112 / 151

Chapter 3: Advanced Configuration

Administration

Page

110

Web Idle timeout

Set the Web Idle timeout time. The webpage can be logged out after
Web Idle Timeout without any operation.

Allowed Remote
IP(IP1,IP2,...)

Set the IP from which a user can login the device remotely.

SSH

Enable/Disable telnet.

Enabling Mangement access for wireless clients

To allow all the wireless clients connected to the cnPilot Home Router to access the management
interface:

Navigate to Administrator tab.

Enable Allow Wireless Host option under Web Access.

The user must have administrator permissions to make this change.

Enabling SNMP access over WAN

To enable SNMP access over WAN:

Navigate to Administrator > SNMP tab.

Enable Remote SNMP Login option.

The user must have administrator permissions to make this change.

Содержание cnPilot R200
























































































































































Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды

Cambium Networks cnPilot R200, Руководство пользователя

Результаты поиска

Содержание cnPilot R200

Отзывы:

Похожие инструкции для cnPilot R200

Бренды по названию

Популярные бренды