background image

- 17 -

Cont ...

 

The unit is fitted with an internal re-settable fuse, see Section 11.

5.26 

Supply cord replacement:

The supply cord and internal wiring within the terminal 
box are routed and secured to ensure compliance with the 
electrical standard EN 60335-1. It is essential that prior to 
any disturbance of this internal wiring, all cable routing and 
securing details are carefully noted to ensure re-assembly to 
the same factory pattern is always maintained.

 

If the supply cord is to be changed or is damaged, it must be replaced with a  

 

 

special cord assembly available from Calpeda Ltd or one of their approved  

 

 repairers.
 

On disassembly note the cord retention and routing system.  Re-assemble to  

 

 

the same pattern.

 

For information on cable connection consult the wiring diagram.

4)  Re-insert connector into the correct location on the control board and route    
 

the cable to the back of the unit and secure with a cable tie to the retainer.

Model

Fuse Size (AMPS)

All models

5

5.24 

RS 485 Modbus – BMS Connection:

 

RS 485 is available on this product for BMS connection and is enabled in the  

 

 

Advanced settings menu.

5.25 

Fuses:  

The following fuse size should be used:

Fig. 19

Retainer

Cable tie

Содержание Unimat-E Series





































Отзывы: