background image

PLEASE ADHERE TO INSTRUCTIONS IN THIS MANUAL

Failure to do so may be dangerous and may 

void certain provisions of your warranty.

For further assistance, please call 24hr hotline: 1-877-325-3473 (U.S.A. and Canada)
Please have model and serial numbers available before calling.

Oakville

1-800-410-3131
1-905-829-4422
F 905-829-4430

Orillia

1-877-325-3473
1-705-325-3473
F 705-325-2106

WARRANTY: 

Under normal use the Company warrants to 

the purchaser that defects in material or workmanship will be 
repaired or replaced without charge for a period of 18 months 
from date of shipment, or 12 months from the start date of 
operation, whichever expires fi rst. Any claim for warranty 
must be reported to the sales offi ce where the product was 
purchased for authorized repair or replacement within the 
terms of this warranty. 

Subject to State or Provincial law to the contrary, the 
Company will not be responsible for any expense for 
installation, removal from service, transportation, or damages 
of any type whatsoever, including damages arising from lack 
of use, business interruptions, or incidental or consequential 
damages.

The Company cannot anticipate or control the conditions of 
product usage and therefore accepts no responsibility for 
the safe application and suitability of its products when used 
alone or in combination with other products. Tests for the 
safe application and suitability of the products are the sole 
responsibility of the user.

This warranty will be void if, in the judgment of the Company, 
the damage, failure or defect is the result of:

• 

Vibration, radiation, erosion, corrosion, process 
contamination, abnormal process conditions, 
temperature and pressures, unusual surges or pulsation, 
fouling, ordinary wear and tear, lack of maintenance, 
incorrectly applied utilities such as voltage, air, 
gas, water, and others or any combination of the 
aforementioned causes not specifi cally allowed for in 
the design conditions or,  

• 

Any act or omission by the Purchaser, its agents, servants 
or independent contractors which for greater certainty, 
but not so as to limit the generality of the foregoing, 
includes physical, chemical or mechanical abuse, 
accident, improper installation of the product, improper 
storage and handling of the product, improper application 
or the misalignment of parts.

No warranty applies to paint fi nishes except for manufacturing 
defects apparent within 30 days from the date of installation.

The Company neither assumes nor authorizes any person to assume 
for it any other obligation or liability in connection with the 
product(s).

The Purchaser agrees that all warranty work required after the 
initial commissioning of the product will be provided only if the 
Company has been paid by the Purchaser in full accordance with 
the terms and conditions of the contract.

The Purchaser agrees that the Company makes no warranty or 
guarantee, express, implied or statutory, (including any warranty 
of merchantability or warranty of fi tness for a particular purpose) 
written or oral, of the Article or incidental labour, except as is 
expressed or contained in the agreement herein.

LIABILITY: 

Technical data contained in the catalog or 

on the website is subject to change without notice. The 
Company reserves the right to make dimensional and other 
design changes as required. The Purchaser acknowledges 
the Company shall not be obligated to modify those articles 
manufactured before the formulation of the changes in design 
or improvements of the products by the Company.

The Company shall not be liable to compensate or indemnify 
the Purchaser, end user or any other party against any actions, 
claims, liabilities, injury, loss, loss of use, loss of business, 
damages, indirect or consequential damages, demands, 
penalties, fi nes, expenses (including legal expenses), costs, 
obligations and causes of action of any kind arising wholly or 
partly from negligence or omission of the user or the misuse, 
incorrect application, unsafe application, incorrect storage and 
handling, incorrect installation, lack of maintenance, improper 
maintenance or improper operation of products furnished by the 
Company.

Edmonton

1-780-466-3178
F 780-468-5904
5918 Roper Road
Alberta, Canada T6B 3E1

Houston

1-800-654-2583
1-713-433-2600
F 713-433-4541

Denver

1-855-244-3128
1-303-979-7339
F 303-979-7350

Содержание CX Series













Отзывы: