background image

13 

1006905 ISSUE 2

Model

CPT6ALY

CPT8ALY

CPT12ALY

CPT15ALY

Refrigerant 

charge 

R32 kg

0.9

1.0

1.5

1.5

Minimum area  m²

6.9

8.5

19.1

19.1

Notes

*Assumed worst case for access category: a - general access and location class: I - mechanical equipment 

in occupied space; both as defined in line with EN378-1 2016 section 5.1 table 4 and section 5.3.

*Min Area is calculated in line with section C.2 on EN378-1 2016 (calculation C.2)

3�2 REFRIGERANT TYPE AND INSTALLED 
LOCATION

This heat pumps CPT6, CPT8, CPT12 and CPT15 
contain R32, which is an environmentally friendly 
refrigerant with a GWP (Global Warming Potential) of 
675. R32 has the safety in use classification of A2L, 
being low toxicity and lower flammability. In practical 
terms it is very difficult to ignite an A2L refrigerant, 
but this classification requires a risk assessment to 
be undertaken for the possibility of refrigerant being 
released by accident into an area connected to the 
heat pump, considering the application, location of 
components, and the installed refrigerant charge. This 
installation guidance can form the framework for such a 
risk assessment for the installation. 

All flammable refrigerants will not ignite if the 
concentration level in a room stays below their lower 
flammability limit (LFL). European standard EN378 
defines requirements to remain far below the lower 
flammable limit in case of accidental leakage. By 
choosing the location as dictated by EN378-1:2016 
the probability of forming a flammable atmosphere 
can be eliminated. Please refer to the minimum 
area for each product and the interpretation below 
regarding locations of heat pump and swimming pool. 
This information is provided as a guide only and does 
not supersede the regulations or health and safety 
requirements

INTERPRETATION

Please refer to the installation situations below for how 
to apply the minimum area stated above. 

Pool outside and heat pump outside:  

Automatically meets the minimum area requirement 
because outside space is unlimited. 

Pool outside and heat pump inside a plant room:  

Automatically meets the minimum area requirement 
because the room must open to the outside for heat 
pump airflow and the outside space is unlimited. 

Pool inside and heat pump outside:  

The pool hall must exceed the minimum area 
requirement shown above.

Pool inside and heat pump inside a plant room, 
isolated from the pool hall:  

The pool hall must exceed the minimum area 
requirement shown above. 

Pool inside and heat pump inside a plant room, 
ventilated to the pool hall:  

The pool hall and plant room combined must exceed 
the minimum area requirement shown above. 

Содержание C-PAC+ CPT12 ALY

































Отзывы: