background image

16

Auxiliary microswitch

Event/condition

Value

DHW tapping in progress

1

Heating cycle in progress

2

Comfort cycle (pre-heating/recirculation) in progress

4

HIU OFF

8

Error not active

16

Error active

32

 

 

 

 

 

 

 

 

   

 

 

 

 

 

 

 

 

 

 

 

 

 

   

 

 

 

 

 

The HIU is equipped with a contact, driven by a relay incorporated in
the circuit board, the intervention logic of which can be programmed
in accordance with requirements by setting technical parameter t05.

Each  event  linked  to  operation  of  the  HIU  is  linked  to  a  numerical
value, according to the following table:

Closing of the contact on the occurrence of multiple events conditions
is programmed by setting parameter t05 to a value corresponding to
the sum of the single events/conditions.
We give some practical examples below:

example 1 - Driving an external primary flow pump, normally OFF.

The  contact  must  be  closed  if  any  HIU  function  is  active  (DHW
production, heating, pre-heating)

Parameter t05 must be set to: 1 + 2 + 4 = 7

This value (t05 = 7) is 

set by default

.

example 2 - Distinction of consumption for DHW production from
total consumption (in combination with heat meter equipped with
dedicated function)

The contact must be closed both if DHW tapping is in progress and if
activation  of  the  comfort  function  is  requested  (pre-heating  or
recirculation).

Parameter t05 must be set to 1 + 4 = 5.

Closing  of  the  microswitch  is  shown  on  the  user  interface  by  the
symbols shown alongside.

N.B.  if  the  DHW  recirculation  function  is  enabled  with  t02  =  1
(see  page  13)  the  auxiliary  microswitch  intervention  logic
described above is not operational. In this case, the contact is
used to control the recirculation pump.

N.B.:  the  auxiliary  microswitch  can  be  used  to  drive  electric
loads directly, taking account of the following operating limits:

- Max voltage:                                                                     230 Vac
- Max current:                                                                             3 A

If  the  electric  load  to  be  controlled  is  not  included  within  the
parameters indicated an external relay must be interposed.

Connection

For information on how to access the dedicated terminals, consult the
“auxiliary microswitch” section on page 19.

Содержание SATK32 Series

























Отзывы: