1
1
CAUTION
This appliance is for outdoor use only! Provide ample ventilation. This gas appliance consumes air (oxygen). Do not use this
appliance in an unventilated space to avoid endangering your life. If still more gas appliances and/or occupants using gas are
added to the space, additional ventilation must be provided.
IMPORTANT
Read these instructions carefully so as to familiarise yourself with the appliance before connecting it to a gas cylinder.
Retain these instructions for future reference.
GB
1. Introduction
• This appliance complies with SANS 1539:2017.
• This appliance shall be used exclusively on CADAC domestic gas cylinders.
• It may be hazardous to attempt to fit the appliance to other types of gas cylinders.
•
Appliance category:
Cylinder Vapour Pressure propane / butane mixture (LPG).
•
Nominal consumption:
203 g/hr
•
Nominal Heat Input:
2.8kW
• This appliance uses a unique No.23 CADAC jet. (See Section 9).
• Gas appliances require ventilation for efficient performance and to ensure the safety of users and other persons in close proximity.
• Use Outdoors Only
2. Safety information
• Check that the seal (K) between the Stem (E) and the gas cylinder is in place and in
good condition before connecting to the gas cylinder (See Fig. 2.)
• Do not use the appliance if it has a damaged or worn seal.
• Do not use an appliance that is leaking, damaged or which does not operate properly.
• Use this appliance only on a firm level surface.
• Ensure the appliance is used away from flammable materials. Minimum safe distances
are: Above the appliance 1.2m. At the rear and sides 0,6m
(See Fig. 1)
• Ensure that the appliance is fitted to the gas cylinder in a well-ventilated location,
preferably outdoors, away from any sources of ignition, such as naked flames, pilots,
electric fires and away from other people.
• If there is a leak on your appliance (smell of gas), take it outside immediately into a
well-ventilated flame free location where the leak may be detected and stopped. If you
wish to check for leaks on your appliance, do it outside.
Do not try to detect leaks using a flame, use soapy water.
• In the event of light back (where the flame burns back and ignites at the jet (G) immediately turn off the gas supply by closing the
cylinder valve using the control knob (See fig. 2). After the flame is extinguished, re-light the appliance as described in Section 4
below. Should the flame light back again, return the appliance to your authorised CADAC repair agent.
3. Assembly Instructions
• The CADAC Grillogas Braai is easy to assemble and prepare for use.
• To fit the stem (E) to the gas cylinder, first check that the cylinder valve is in the “off” position by turning the control knob clockwise
to its “stop” (See Fig. 2). Screw the stem into the cylinder in a clockwise direction until it is fully engaged.
• Tighten by hand only.
Grill Plate
(740-10-ZA)
• Place the burner base plate (L) plate on the stem (E), making sure that the burner tube fully engages on the stem (E).
• Place the burner pan (B) onto the burner base plate and stem.
• Place the Grill Plate (A)in the burner pan, making sure that it sits properly on the locators (J).
BBQ Grid
(740-20-ZA)
• Place the burner base plate (L) plate on the stem (E), making sure that the burner tube fully engages on the stem (E).
• Place the burner pan (B) onto the burner base plate and stem.
• Place the BBQ Grid (F) in the burner pan, making sure that it sits properly on the locators (J).
•
WARNING!: Your BBQ Grid has a non-stick PTFE coating. Avoid using abrasive cooking utensils and cleaners, as this may damage its
surface.
Paella Pan Mini
• Place the burner base plate (L) plate on the stem (E), making sure that the burner tube fully engages on the stem (E).
• Place the burner pan (B) onto the burner base plate and stem.
• Place the pot/ paella stand (D) on the burner pan, ensuring that the three hooks sit correctly over the outer rim of the Burner Pan (B)
• Place the paella pan mini, onto the pot / paella stand (D).
•
WARNING!: When pre-heating, do not use the paella pan mini on a high-flame setting for more than 15 minutes, as this can damage
the non-stick coating and the pan
Pots
• Place the burner base plate (L) plate on the stem (E), making sure that the burner tube fully engages on the stem (E).
• Place the burner pan (B) onto the burner base plate and stem.
• Place the pot/ paella stand (D) on the burner pan, ensuring that the three hooks sit correctly over the outer rim of the Burner Pan (B)
• Place a pot, onto the pot / paella stand (D). Please note, the pot size must not exceed 340mm in diameter.
Fig. 1
Содержание GRILLOGAS BRAAI
Страница 2: ......