9
Sleep Mode
This mode is used to conserve energy and can be used when the
unit is in the COOL, HEAT or DRY mode only.
For Cooling Mode:
S
Push the SLEEP button. The SLEEP display will appear
on the remote control.
OPER
ºF
ºC
HOUR
ON/OFF
:
A09644
S
After 1 hour the set point will be raised by 1.8
_
F (1
_
C).
S
After another hour, the set point will be raised by another
1.8
_
F (1
_
C) and the fan will run in low speed.
S
The SLEEP mode will be cancelled when the SLEEP
button is pushed again.
For Heating Mode:
S
Same as cooling mode but set points will be lowered by
1.8
_
F (1
_
C) and the HEAT icon will disappear from the
display panel.
Timer Function
TIMER ON (to start the unit) and TIMER OFF (to stop the unit)
can be used separately or together. The clock on the remote control
must be set before using this function.
Timer ON only
ºF
ºC
HOUR
:
OPER
Only ON
is displayed.
ON
A09639
This function will allow the unit to start automatically at the set
time. The TIMER ON can be set while the unit is on or off.
To set the TIMER ON function, perform the following:
1. Push the “TIMER ON” button once.
2. The clock indicator
and time will not be displayed on
the remote control. The default “TIMER ON” time (first
time function is used) or the last time setting will be
displayed and “ON” will flash.
3. Push the “--” or “+” within 5 seconds until the desired on
time is displayed.
NOTE: Pressing the “--” or “+” will decrease or increase the
time in 1 minute increments.
Pressing the “--” or “+” continuously will decrease or increase
the time in 10 minute increments.
4. Push the “TIMER ON” again. The “ON” icon will stop
blinking and the time at which the unit will start is set. The
clock indicator
and the time will be displayed again.
The “TIMER ON” time will be stored in memory indefinitely until
it is cancelled by the user by pushing the “TIMER ON” button or
the remote control batteries are replaced.
If the unit is running and the “TIMER ON” set time is reached, the
unit will continue operating normally.
NOTE: When the unit is shut off by the user using the
“ON/OFF” button, and if the “TIMER ON” is set, the
following will be displayed on the remote control.
-- Set Point
-- Time
-- Clock indicator
next to time indicates TIMER ON is set.
On the display panel, the operation light will turn red.
When the “TIMER ON” set time is reached, the display on the
remote does not change, but the unit will run as indicated by the
operation light on the front cover turning green. To get display on
the remote, push the “ON/OFF” button once.
Timer OFF only
This function will allow the unit to stop automatically at the set
time. The timer can be set while the unit is on or while it is off.
To set the “TIMER OFF” function, perform the following:
1. Push the “TIMER OFF” button once.
2. The clock indicator
and time will not be displayed.
“OFF” will be flashing.
3. Push the “--” or “+” button within 5 seconds until the
desired ON time is displayed.
NOTE: Pressing the “ --” or “+” will decrease or increase the
time in 1 minute increments.
Pressing the “--” or “+” continuously, will decrease or increase
the time in 10 minute increments.
4. Push the “TIMER OFF” button again, the “OFF” icon will
stop blinking and the time at which the unit will turn off is
set. The clock indicator
and the time will be displayed
again.
The “TIMER OFF” time will be stored in memory indefinitely
until is is cancelled by pushing the the “TIMER OFF” button or
the batteries are replaced in the remote control.
If the unit is running and the “TIMER OFF” set time is reached,
the unit will turn off and the operation indicator light on the front
panel will turn red. The display on the remote control will remain
the same as when the unit was running. To turn the unit on again,
push the “ON/OFF” button twice. The operation indicator light on
the front panel will turn green.
Timer ON and Timer OFF
ºF
ºC
HOUR
:
OPER
ON/OFF will
be displayed
ON/OFF
A09643
Use both functions as described in “TIMER ON” and “TIMER
OFF” sections to program the unit to turn on and shut off at
specified times. Times will be stored in memory until cancelled
by user or the remote control batteries are replaced.
