background image

The SmartSwitch 7000 Chassis View

2-24

Managing the Hub

Figure 2-12. Port ConÞguration

Use the options in this window to select the desired mode:

Standard Mode

In Standard Mode, an interface can only either transmit 

or

 receive at any given 

time, and must wait for one activity to be completed before switching to the next 
activity (receive or transmit). In this mode, standard wire speeds (10 Mbps for 
Ethernet, 100 Mbps for FDDI) are available.

Full Duplex

In Full Duplex Mode, an interface can both receive 

and

 transmit packets at the 

same time, effectively doubling the available wire speed to 20 Mbps (for Ethernet) 
or 200 Mbps (for FDDI).

Be sure to click on 

 to set your changes; note that the interfaceÕs current 

mode can be determined by the Þeld selected in the window.

Configuring Fast Ethernet Ports

If you have any Fast Ethernet NIMs installed in your SmartSwitch 7000 chassis, 
the Port ConÞguration window available for those ports allows you to both view 
and set that portÕs available modes. All 100Base-TX Fast Ethernet ports can be 
conÞgured to operate in either standard Ethernet (10 Mbps) or Fast Ethernet (100 
Mbps) mode, and in each mode can be conÞgured to operate in Full Duplex, 
effectively doubling the available wire speed (from 10 to 20 Mbps in standard 
Ethernet mode, or from 100 to 200 Mbps in Fast Ethernet mode); 100Base-FX 
(Þber) ports can be conÞgured to operate in their standard 100 Mbps mode, or in 
full duplex mode. This window also displays the mode currently in effect on the 
selected interface, and provides some information (where it is available) about the 
interfaceÕs link partner.

TIP

Note that, if you select the ConÞguration option available for a Fast Ethernet interface, an 
entirely different window will appear; see 

ConÞguring Fast Ethernet Ports

, below, for 

information on conÞguring these ports.

Содержание Lancast Media Converter 7000













































































































Отзывы: