background image

 

ii

 

FCC NOTICE

 

FCC NOTICE

 

This device complies with Part 15 of the FCC rules. Operation is 
subject to the following two conditions: (1) this device may not 
cause harmful interference, and (2) this device must accept any 
interference received, including interference that may cause 
undesired operation.

 

NOTE:

 

 This equipment has been tested and found to comply with 

the limits for a Class A digital device, pursuant to Part 15 of the 
FCC rules. These limits are designed to provide reasonable 
protection against harmful interference when the equipment is 
operated in a commercial environment. This equipment uses, 
generates, and can radiate radio frequency energy and if not 
installed in accordance with the operator’s manual, may cause 
harmful interference to radio communications. Operation of this 
equipment in a residential area is likely to cause interference in 
which case the user will be required to correct the interference at 
his own expense.

 

WARNING:

 

 Changes or modifications made to this device which 

are not expressly approved by the party responsible for 
compliance could void the user’s authority to operate the 
equipment.

 

DOC NOTICE

 

This digital apparatus does not exceed the Class A limits for radio 
noise emissions from digital apparatus set out in the Radio 
Interference Regulations of the Canadian Department of 
Communications.

Le présent appareil numérique n’émet pas de bruits 
radioélectriques dépassant les limites applicables aux appareils 
numériques de la class A prescrites dans le Règlement sur le 
brouillage radioélectrique édicté par le ministère des 
Communications du Canada.

 

F60XXprintcover Book  Page ii  Friday, April 19, 1996  9:14 AM

Содержание F6019





































Отзывы: