background image

 

EMC37-12 USER’S GUIDE

iii

 

CABLETRON SYSTEMS, INC.

PROGRAM LICENSE AGREEMENT 

 

IMPORTANT

 

:

Before utilizing this product, carefully read this License Agreement.

This document is an agreement between you, the end user, and Cabletron Systems, Inc. (“Cabletron”) 
that sets forth your rights and obligations with respect to the Cabletron software program (the 
“Program”) contained in this package. The Program may be contained in firmware, chips or other 
media. BY UTILIZING THE ENCLOSED PRODUCT, YOU ARE AGREEING TO BECOME 
BOUND BY THE TERMS OF THIS AGREEMENT, WHICH INCLUDES THE LICENSE AND 
THE LIMITATION OF WARRANTY AND DISCLAIMER OF LIABILITY. IF YOU DO NOT 
AGREE TO THE TERMS OF THIS AGREEMENT, PROMPTLY RETURN THE UNUSED 
PRODUCT TO THE PLACE OF PURCHASE FOR A FULL REFUND.

 

CABLETRON SOFTWARE PROGRAM LICENSE

 

1.    LICENSE. 

You have the right to use only the one (1) copy of the Program provided in this 

package subject to the terms and conditions of this License Agreement.

You may not copy, reproduce or transmit any part of the Program except as permitted by the 
Copyright Act of the United States or as authorized in writing by Cabletron.

2.    OTHER RESTRICTIONS.

You may not reverse engineer, decompile, or disassemble the 

Program.

3.    APPLICABLE LAW. 

This License Agreement shall be interpreted and governed under the 

laws and in the state and federal courts of New Hampshire. You accept the personal jurisdiction and 
venue of the New Hampshire courts.

Содержание EMC37-12































Отзывы: