-6-
OPERATING INSTRUCTIONS
1. Place the
Arrow Saw
on a
flat, level work surface.
2. Place the
Shaft Position Bracket
onto
the
Base
.
3. Locate the left face of the
Shaft Position
Bracket
at the line on the
Measuring Tape
indicating the length of shaft you want to
cut. For example, if you want to cut a 31”
long arrow shaft, locate the
Shaft Position
Bracket
face at the 31” mark.
Figure 4
4. Secure the
Shaft Position Bracket
to the
Base
by tightening the
Wing Nut
.
Slowly tighten the
Wing Nut
while firmly
holding the
Shaft Position Bracket
to
prevent the
Shaft Position Bracket
from
moving.
5. Continue to the “THROUGH CUTS” or
“ROLL CUTS” section of this manual.
MEASURING TAPE APPLICATION
The
Arrow Saw with Dust Collecting Attachment
comes without the
Measuring
Tape
applied. Carefully follow these instructions to apply the
Measuring Tape
to
ensure you get the best results from your
Arrow Saw
.
1. Place the
Arrow Saw
on a flat, level, non-skid work surface.
2. Clean the front face of the
Base
to remove any dirt or grime that may have
accumulated during manufacturing.
3. Place the end of a tape measure
firmly against the right side of the
Cutting Blade
.
Figure 3
4. Measure 6” (15.2 cm) from the
Blade
to the back face of the notch
in the
Shaft Position Bracket.
5. Using the left face of the
Shaft
Position Bracket
as a guide, mark
the
Base
with a pencil.
6. Cut the
Measuring Tape
at the
5” mark.
Figure 3
7. Peel about 4” (10.2 cm) of the
backing off of the
Measuring Tape
exposing the adhesive surface.
8. Line up the 6” indicator line on the
Measuring Tape
with the left side of the
Shaft
Position Bracket
. The top of the
Measuring Tape
should be about 1/2” (1.3 cm)
below the top of the Base. Carefully apply the
Measuring Tape
a few inches at a
time. Continue peeling off the backing as necessary.
9. Be sure to apply the
Measuring Tape
level and without air bubbles or creases.
Such irregularities will result in inaccurate shaft length measurements.
FIGURE 3
Left
Face
of Shaft
Position
Bracket
Shaft
Position
Bracket
Right Side
of
Cutting
Blade
Measuring
Tape
Front
Face
of
Base
WARNING!
READ AND FULLY UNDERSTAND ALL INSTRUCTIONS
AND WARNINGS PRIOR TO USING THIS SAW.
YOUR SAFETY IS MOST IMPORTANT! FAILURE TO
COMPLY WITH PROCEDURES AND SAFE GUARDS
MAY RESULT IN SERIOUS INJURY OR PROPERTY
DAMAGE. REMEMBER: YOUR PERSONAL SAFETY
IS YOUR RESPONSIBILITY!
WARNING!
Before cleaning, assembling or disassembling the Arrow
Saw, make sure it is turned OFF and the PLUG IS REMOVED FROM THE
OUTLET/POWER SOURCE!
FIGURE 4
Shaft
Position
Bracket
Base
Bracket
Face
Wing Nut
-7-
WARNING!
Before cleaning, assembling or disassembling the Arrow
Saw, make sure it is turned OFF and the PLUG IS REMOVED FROM THE
OUTLET/POWER SOURCE!
WARNING!
Be sure to follow ALL
SAFETY WARNINGS
and precautions that
are contained in this
instruction manual
before using this
appliance!
WARNING!
Be sure to follow ALL
SAFETY WARNINGS
and precautions that
are contained in this
instruction manual
before using this
appliance!
CAUTION ROTATING SHARP BLADE!
To avoid severe injury keep fingers, hands and other foreign
objects clear of the saw opening Blade and Moving Parts of the
Arrow Saw. Wear approved Safety Glasses and Kevlar Gloves
when using the Arrow Saw.
CAUTION ROTATING SHARP BLADE!
To avoid severe injury keep fingers, hands and other foreign
objects clear of the saw opening Blade and Moving Parts of the
Arrow Saw. Wear approved Safety Glasses and Kevlar Gloves
when using the Arrow Saw.
