CAB Hermes Series Скачать руководство пользователя страница 52

Страница: 52 / 71

cab - Produkttechnik GmbH

ONL key

Switch into OFFLINE mode (LED ONL off)

FF key

Provides label feed. The leading edge of the next label to be
printed is in print position.

CAN key

Deletes data of the previous print job in internal memory.
Following that, "Pause reprint" is not available.
(see PSE key)

PSE key

Repeats the print of the last label, after the previous print job has
been completed. (only if setup parameter 'Pause reprint' is on)

ONL key

Pressing both keys together for at least 5 seconds will switch

into the SETUP mode.

CAN key

(LED ONL off)

System Mode ONLINE

ONL key

Switch into ONLINE mode (LED ONL on)

FF key

Provides label feed. The leading edge of the next label to be
printed is in print position.

CAN key

Switch into LABEL FROM CARD mode.
(only if memory card is installed and formats are stored it)

PSE key

Display shows current printer mode

System Mode OFFLINE

System Mode PRINT

CAN key

short pressing :

Cancels the current print job,
Switch to the next job in the input buffer

longer pressing (>1s): Cancels the current print job,

Deletes the input buffer
(LED CAN blinks),
Switch into ONLINE mode

PSE key

Interrupts the current print job,
Switch into PAUSE mode (LED PSE on)

Содержание Hermes Series








































































Результаты поиска

Содержание Hermes Series

Отзывы:

Бренды по названию

Популярные бренды

CAB Hermes Series, Техническая информация

Результаты поиска

Содержание Hermes Series

Отзывы:

Бренды по названию

Популярные бренды