C-TEC QT302RXS Скачать руководство пользователя страница 9

SLAVE OVERDOOR LIGHTS

Slave overdoor lights comprise two red and two green ultra-bright LEDs
inside a triangular diffuser.  They offer low current consumption and
connect to call points via four cores (Two cores are the same as the two
network wires so connection to the network can be made at the
overdoor light or the call point).

QT606 .................. Quantec Overdoor Light

CEILING PULLS

Ceiling pulls have a red confidence light and a 3m cord with
two open-sided triangular pulls specially designed for ease of
use by the infirm.  Four knockouts are provided for 16mm square
mini trunking and the backplate fits BESA centres.  They
are generally reset at a call point to which they connect via
three cores.

QT607 .................. Quantec Ceiling Pull

SLAVE CALL POINTS

Slave call points are functionally the same as ceiling pulls and as such must
be used in conjunction with a master call point.  Comprising a call button,
remote socket and confidence light, they are designed for use in areas
such as double bedrooms where more than one call button may be
required.  All calls must be reset at the master.

QT602D ................ Quantec Slave Call Point

TAIL CALL BUTTONS

Tail call buttons consist of a pear-shaped push, a lead and a plug
that connects it to a call point’s remote socket.  A call is made by
pressing the button or by pulling the plug out.  Tail call leads are
available in a variety of different lengths (as indicated below) to
suit different applications.

NC805C/6 ............. 1.8m (6ft) tail call button with right angle plug
NC805C/14 ........... 4.2m (14ft) tail call button with right angle plug
NC805D ................ 1.2-3.6m (4-12ft) tail call button with coiled lead

HAND/FOOT OPERATED PNEUMATIC PADS

Ideal for patients who find it difficult to press buttons,
Quantec’s hand/foot operated pneumatic pad must be
used in conjunction with the NC805AS air switch.
Applying pressure to the pad operates the air switch
which, when connected to a call point’s remote socket,
triggers a call.

NC805P ................ Hand/Foot Operated Pneumatic Pad
NC805AS .............. Remote Air Switch, for use with NC805P

ANCILLARY DEVICES

CALL

Q

Approved Document No: DNSQ100101 Rev 6 • Page 9 of 16

Содержание QT302RXS

















Отзывы: