DIGITAL TO ANALOG CONVERTER DA 0 3.0
DA 0 3.0 User's Manual
4
5
8)
POWER CORD PROTECTION
: Protect the power cord from being walked on or pinched
particularly at plugs, convenience receptacles and the point where they exit from the unit.
9)
LIGHTNING
: Unplug this unit during lightning storms or when unused for long period of
time.
10)
SERVICING
: Refer all servicing to qualified service personnel. Servicing is required
when the unit has been damaged in any way, such as if the power-supply cord or plug is
damaged, liquid has been spilled inside the appliance or it has been exposed to moisture,
the appliance does not operate normally, or has been dropped.
11)
DO NOT OPEN THE CABINET
: There are no user serviceable
components inside this product. Opening the cabinet may present
ashockhazardandanymodificationtotheproductwillvoidyour
warranty.
12)
WARNING
:Toreducetheriskoffireorelectricshock,donotexposethisunittorainor
moisture.
CAUTION:
▷
DO NOT EXPOSE THIS APPLIANCE TO DRIPS OR SPLASHES.
▷
DO NOT PLACE ANY OBJECTS FILLED WITH LIQUIDS, SUCH AS VASES, ON THIS
APPLIANCE.
▷
DO NOT INSTALL THIS APPLIANCE IN A CONFINED SPACE, SUCH AS WITHIN A
BOOKCASE OR SIMILAR PIECE OF FURNITURE.
▷
PLUG THE AC POWER CORD INTO AN EASILY ACCESSIBLE AC WALL OUTLET,
SO IT CAN BE QUICKLY UNPLUGGED IN CASE OF EMERGENCY.
▷
DO NOT REMOVE THE PROTECTIVE HOUSING WITH A SCREWDRIVER.
▷
USE OF CONTROLS OR ADJUSTMENTS OR PERFORMANCE OF PROCEDURES
OTHER THAN THOSE SPECIFIED HEREIN MAY RESULT IN HAZARDOUS
RADIATION EXPOSURE.
▷
IF THIS APPLIANCE SEEMS TO BE MALFUNCTIONING, CONTACT A QUALIFIED
SERVICE STATION. DISCONTINUE USE OF ANY MALFUCTIONING UNIT.
Unpacking and Installation
This section describes the unpacking and installation procedures for your new component.
❶
Unpacking
All shipping boxes have been specially designed to protect their contents and
special care has been taken to prevent damage under normal shipping conditions.
Mishandling should be evident upon inspection of the shipping container. Carefully
remove your new component from its packing and examine it closely for signs of
shipping damage. We strongly recommend saving all original packing to protect your
component from damage should you wish to store it or ship it at a later date.
❷
Installation
▷
BE CERTAIN TO INSTALL THE UNIT IN A SECURE LOCATION FROM WHICH IT
CAN NOT FALL OR TIP OVER
▷
Provide adequate ventilation - the chassis will become warm in normal use. Do not
operateoncarpetoranyothersurfacethatmightblockairflow
▷
Do not allow the chassis to touch any metal parts, such as the frame of an
equipment rack. This might create a parallel ground path that could degrade the
sound of your system
▷
Connect the input and output cables. Input connection is via COAX , AES/EBU
TOSLINK or USB. Output can be via RCA or XLR jacks
IMPORTANT
: READ THE SECTIONS “BACK PANEL”
WARNING
: The unit should be operated only at rated voltage, indicated on the
power connector. If you are not sure what is the mains voltage supplied to your
home, consult with your unit dealer.
▷
Connect the power supply to the power source indicated on the rear panel.
Avoid power conditioners that float the ground pin. ALWAYS connect power
cord to component before plugging it into an AC outlet, and make sure that
unit main switch is set to the „off” position before making the final connection.
For best performance, try to route the power cord away from signal cables.
Pay close attention to power quality, and be aware that different power cords can alter
the sound.
Important Safety Instructions
AC POWER CORD CONNECTION
CAUTION:
TO PREVENT ELECTRIC SHOCK, MATCH THE BLADE
WIDTH OF THE PLUG TO THE SLOT WIDTH. THE PLUG
MUST BE FULLY INSERTED TO THE SLOT.
For CANADA
