BYOC Classic Brit 50 Скачать руководство пользователя страница 115 | Manualshive

Страница: 115 / 127

BYOC Classic Brit 50 Скачать руководство пользователя страница 115

115

Turning your amp on for the first time

Step 1: Make sure your AC power cord is NOT plugged in. Do NOT install any of the tubes yet. Do not plug a
speaker into the speaker jack. Do not plug any instruments into the input jacks. If at any point in this process, you
smell smoke, see sparks, or hear any loud electrical hum noises, immediately pull the AC power cord from the wall
socket.

Step 2: Do not test your amp on a metal table or any surface that can conduct electricity. Situate yourself and your
amp so that the AC power outlet you will be using is within arm's length.

Step 3: Install your amplifier chassis into the cabinet or enclosure that you should have. You should never apply
power to the amplifier while it is not inside its cabinet or enclosure. If you insist on supplying power to the
amplifier while it is not inside its cabinet or enclosure, the safest way to do so is with the chassis laying on a non-
conductive, flame retardant surface with the transformer side facing down and the open side of the chassis facing
up, making sure that no foreign objects (especially any of your body parts) are touching any part of the amp.

Step 4: Install the 3A (120v) or 2A (240v) fuse into the panel mounted fuse holder on the back of the chassis. You
can tell the 2A or 3A fuse apart from the 500mA fuse because the 2A or 3A fuse will have a small “2” or “3”
printed on it and the 500mA fuse will have “500” printed on it somewhere. You can also tell because the the 2A or
3A fuse will have a thicker conductive wire running through the middle of it than the 500mA.

Step 5: Turn the amplifier's power switch on, but still do not plug the power cord in yet.

Step 6: Orient the amp so that you can see the indicator light. When you plug the power cord into the AC power
supply, you should be able to see the indicator light come on immediately. This means, at the very least, AC
power is getting to the power transformer and that the power transformer is working.

«
...
113
114
115
116
117
...
»

Содержание Classic Brit 50
































































































































Отзывы:

Нет отзывов