manualshive.com logo in svg

BYD F3, Руководство пользователя

Скачайте бесплатно руководство по эксплуатации "4DRC F3" с нашего сайта. В этом руководстве вы найдете подробные инструкции по использованию вашего устройства. Не забудьте загрузить его с manualshive.com для наилучшего опыта использования продукта.

Поделиться
Скачать
background image

                                                         F3/F3R  OWNER’S  MANUAL 

 

- 79 - 

discharged. 
If it comes on while you are driving, there is a 
problem somewhere in the charging system. 
The engine ignition will continue to operate 
until the battery is discharged, however. Turn 
off the air conditioning, blower, radio, etc., 
and drive directly to the nearest BYD AUTO 
service station. 

(d)  Low engine oil pressure warning light 

This light warns that the engine oil pressure is 
too low. 
If it flickers or stays on while you are driving, 
pull over to a safe place and stop the engine 
immediately. Call a BYD AUTO service 
station for assistance. 
The light may occasionally flicker when the 
engine is idling or it may illuminate briefly 

after a hard stop. There is no cause for 
concern if it then goes out when the engine is 
accelerated slightly. 
The warning light will be on if the level of oil is 
low as well. This light   
isn’t designed to indicate the low oil level. The 
oil level must be inspected by oil dip rod. 
 

NOTICE 

Do not drive the vehicle with the 
warning light on — even for one block. 
It may ruin the engine. 

(e) Malfunction indicator light 

This light comes on when the electronic 
injection system of the engine fails to work. 
If it comes on, contact your BYD AUTO 
service station as soon as possible. 

 

(f) Low fuel level warning light 

When the fuel is nearly empty, the   
light will be on. Please fill the fuel at once. 
When driving on the slope or taking a turning, 
the light would usually be on   
earlier because the fuel in tank will swash. 

 
(g) “ABS” warning light 

The light comes on when the ignition switch is 
turned to the “ON” position. If there is no 
malfunction about the ABS, the light will be 
off in few seconds. Then, the light would be 
on again caused by any malfunction of the 
system. 
When the “ABS” warning light is on (and the 
brake system warning light is off), the 

Содержание F3










































































































































































































































Отзывы:

Нет отзывов

Похожие инструкции для F3

Camcar 40104 Mounting Instructions preview
40104
Бренд: Camcar Страницы: 6
AccuAir AA-4397 Installation Manual preview
AA-4397
Бренд: AccuAir Страницы: 40
Peak PKC0RG Owner'S Manual preview
PKC0RG
Бренд: Peak Страницы: 10
Calix M5T 187A Assembly Instructions preview
M5T 187A
Бренд: Calix Страницы: 5
GMC 2005 Sierra Denali Owner'S Manual preview
2005 Sierra Denali
Бренд: GMC Страницы: 428
Mercedes-Benz GLA 250 2019 Operator'S Manual preview
GLA 250 2019
Бренд: Mercedes-Benz Страницы: 346
Thule Kit 1514 Instructions preview
Kit 1514
Бренд: Thule Страницы: 4
BMW 01 29 9 416 497 Installation Instructions preview
01 29 9 416 497
Бренд: BMW Страницы: 5
WABCO TP19108 Installation Manual preview
TP19108
Бренд: WABCO Страницы: 32
K&M MILSCO KIT# C746700 Installation Manual preview
MILSCO KIT# C746700
Бренд: K&M Страницы: 2
Car-Interface CI-RL4-NAC12 Manual preview
CI-RL4-NAC12
Бренд: Car-Interface Страницы: 25
Thule 2 Bike Carrier 977 Instructions Manual preview
2 Bike Carrier 977
Бренд: Thule Страницы: 6
Tellur BASIC TLL171231 User Manual preview
BASIC TLL171231
Бренд: Tellur Страницы: 5
SAN HIMA SGBR015 Installation Instructions Manual preview
SGBR015
Бренд: SAN HIMA Страницы: 10
AMP Research BEDXTENDER HD MAX 74841-00A Assembly Installation Manual preview
BEDXTENDER HD MAX 74841-00A
Бренд: AMP Research Страницы: 9
Belkin F8V7058-APL User Manual preview
F8V7058-APL
Бренд: Belkin Страницы: 2
Racelogic Speed & Route Profiler Manual preview
Speed & Route Profiler
Бренд: Racelogic Страницы: 24
Toyota Solara guide Owner'S Manual preview
Solara guide
Бренд: Toyota Страницы: 497

Бренды по названию

Популярные бренды

Загрузить еще бренды