By Firstech MA580 Скачать руководство пользователя страница 10 | Manualshive

Страница: 10 / 14

By Firstech MA580 Скачать руководство пользователя страница 10

19 By Firstech, LLC

By Firstech, LLC 18

Option Programming for Four Button Remotes for FM or SS Units

Installation of AM Antennas

Option Programming with Programming Button for AM Units

Step1:

For Programming menu 1: Press Buttons (I+II) for 2 seconds. For Programming menu 2: Press Buttons (I+IV) for 2 seconds.

The car will chirp once indicating that you are in programming mode.

Step2: Within a 2 seconds

after pressing (I+II) or (I+IV), press Button IV the number of times to go to the option number you want to change.

You have to hear a chirp and see the parking light flash each time when you press Button

IV.

Step3 :

Wait a few seconds. You will hear a number of chirps and see a number of parking light flashes corresponding to the option number you want to change.

If the number of chirps or flashes is not what you want, go back to Step 1.

Step4 :

Press ButtonI for the default factory settings and your car will respond by one chirp and one flash. Press Button II for the optional setting and your car

will respond by two chirps and two parking flashes.

ᵉ

ᵉ

If you see an extended flash of the lights, you are going out of programming mode, please go back to Step 1.

ᵉ

ᵉ

If you want to change more options, go back to Step 1.

ᶀ

ᶀ

Resetting any Option Setting to the Factory Setting

Step1:

Press Buttons (I+II) simultaneously or Buttons (I+IV) simultaneously for 2 seconds. A one flash of the parking lights confirms step 1.

Step2:

Press Button III three times. This is confirmed by a parking light flash each time you press Button III. A few second later, your cars parking lights will

flash three times rapidly. Your car is now set to all of the original factory default settings.

The antennas have been calibrated for horizontal installation at the left-top corner of the windshield. Different installation may adversely affect the
transmitting distance.

CANADIAN MODELS ONLY. THE US MODELS DO NOT HAVE THE BUTTON.

Most of the original programming

(

ᴘ

ᴘ

Factory Setting

ᴙ

ᴙ

)

from the factory can be changed to alternative programming

(

ᴘ

ᴘ

Option Setting

ᴙ

ᴙ

)

by Programming

Switch (hereinafter called

ᴘ

PS

ᴙ

).

LED

Programming Button

«
...
8
9
10
11
12
...
»

Содержание MA580















Отзывы:

Нет отзывов