background image

05 Installing the Filter Head and Bracket [14]

To install the filter system, choose a location that enables 
simple connection to the water mains and tap. The 
distance between the filter cartridge and the floor should 
be a minimum of 65 mm to allow adequate space for 
installing the filter cartridge. The filter system must be 
securely fitted to a suitably robust surface using the filter 
bracket supplied. Remove the bracket from the filter head 
and use as a template to mark the appropriate location. 
Drill two pilot holes and fasten the bracket using two 
suitable screws or bolts (not supplied). Correctly fitting the 
mounting bracket will support the weight of the filter and 
help prevent strain on the attached pipes and fittings.  

06 Connecting the filtered water supply 

Attach the 7/16 x 1/4 Push - fit adaptor  [15] to the 
threaded tap tube being careful not to over tighten. 

Using a sharp hobby knife or similar cut the blue flexible 

hose [12] to a suitable length for it to reach between the 

Push -  fit adaptor [15] and filter head [14] remember to 

allow sufficient  length so that it can be routed with out 

kinks and be kept clear of any sharp edges.  

With the tube cut squarely ensure the end is clean and 

smooth before (A) pushing firmly and fully into the adaptor 

fitted to the tap, (B) pull back slightly to effect a water tight 

seal.  

Carefully fit the 3/8 x 1/4  ‘push - fit adaptor’ [16] to outlet 

side of the filter head [14] taking care not to over tighten, 

and then slide the filter head into the bracket taking care to 

observe the direction of flow indicated by the arrow shown. 

Now take the  other end of the blue flexible tube [12]  and 
push firmly  and fully (D) into the adaptor [16], pull back 
slightly to effect a  seal (E) 

Place rubber washers [08] into the nuts on the braided 
hose [17]  and connect to the previously fitted T piece

 [07]

 

tightening to effect a water tight seal.

 

Connect the other 

end to the inlet side of the filter head

 

[14]

 

do not over 

tighten.

Base of Tap 

Filtered Water 

supply 

16

X2

X2

Mains water 

Supply 

Cold water 

Tap 

07

7

0

8

17

Содержание BWTDWFK-TRIFLO









Отзывы: